Hey Ya'll,
Thanks for the input. It's valuable and well appreciated. One other thing I
thought of is that this car has truck arms and I can easily drop the front
mounts to give a greater pinion angle for more forward bite. Anybody had
experience or thoughts on that?
Thanks Doug,
I had 40 lbs front & rear. I guess I can go lower in the rear but don't want
too much drag.
>How much air pressure are you running? Soften the rear springs and
>shocks. The tires will grip better the less air you run up to the point
>where it gets wormy on you. Air up the fronts and crank as much caster
>as you can in it.
Thanks Skip,
Yes the timing and engine were not touched, the rear already has soft
springs/shocks, but I am going a little softer on tires. I agree to not
change too many things at once but I'm in too much of a hurry.
>Hi Grib,
>Assuming that the timing (cam and dist) is the same as last year. I think
>hat I'd put new, softer tires, soften the rear suspension and not change
>too many things at once. Winston Cup guys are probably right in the gear
>ratio question.
S>kip
Thanks Jim,
Yes a softer compound is going to be parts of the mix, however, you know
less rubber is less friction.
Thanks Keith,
I've thought about the combo of 1st gear and rear gear. Perhaps the 2.50 and
3.10 combo is best? I'm not concerned about spinning the tires but I'd sure
like to hook up better. I am going to 27.5" tires and 2" wider, also softer
compound.
Thanks John,
Yes I agree about the 3.10 but I'm afraid about the tall 1st gear. Probably
end up with the 250.
----- Original Message -----
From: "John Beckett" <landspeedracer@email.msn.com>
To: "rgribble" <rgribble@carolina.rr.com>; <land-speed@autox.team.net>
Sent: Tuesday, May 08, 2001 5:44 PM
Subject: Re: opinions wanted
> Grib
>
> To run 200 MPH at 7,800 RPM you will need a 3.18 gear. A 3.25 gear should
> get you 200 MPH at 8,000 RPM.
> Based on your 195 MPH runs at 6,700 RPM, I'd say a 3.0 gear will get you
200
> MPH at 7,400 RPM, but a 3.10 or 3.15 would be better.
>
> As for the trans a 2.20 or 2.30 first gear would be a better deal, but
hard
> to start off from the line without a push start.
>
> JB
>
>
> ----- Original Message -----
> From: "rgribble" <rgribble@carolina.rr.com>
> To: <land-speed@autox.team.net>
> Sent: Tuesday, May 08, 2001 11:41 PM
> Subject: opinions wanted
>
>
> > Hi Everyone,
> >
> > I've got some decisions to make regarding transmission & rear gear
> selection
> > and thought with this vast cache of knowledge, I could get some opinions
> that
> > would help me with mine.
> >
> > I have a Busch Grand National (Winston Cup) 97 Tbird that I run at
Maxton.
> It
> > has given me rides at 204+ MPH last year. It's hard to do a direct
> comparison
> > from last to this year's setup but I've made some changes and now I
can't
> get
> > to Two. I don't know what loss I've got in motor (nothing's been done to
> it)
> > I'm working on a replacement power plant and hope to have it for this
next
> > meet.
> >
> > It seems to me to be a loosing lot in getting through 1st & 2nd gear.
> It's
> > 3200 lbs.( 45% rear wheels) with approx. 650 HP. The transmission I'm
> > presently running is a Super T10 ( w/264,175,133,1 gears) with a 2.75
rear
> > gear and twisting about 6700 in the traps. (should be 7500-8000). My
tires
> are
> > Winston Cup/Goodyear 15" x 10"wide and 28"tall.
> >
> > The biggest problem I experience is that I get a lot of wheel spin in
1st
> and
> > 2nd gears. Any attempt to go WOT and it spins, so much that I have to
use
> my
> > traction control (lift my big toe) to avoid it. I feel that this is
> robbing me
> > of a lot of performance.
> >
> > For the next meet I plan on changing the tires, rear gear and tranny and
> would
> > welcome any thoughts.
> >
> > I'm planning on using a 27.5" tall tire with a 12" width. That's a ="
> smaller
> > which is about 4 MPH, but the additional width may get me a better bite.
> > (don't know about the drag the bigger tire would create?)
> >
> > I have the unique position of being able to put in a Super T101 tranny
(w/
> > square cut gears and full roller bearings by Tex Racing) with any gear
> > selection I want ( which is what I'm not sure of ). I can run any Ford
9"
> rear
> > gear ratio I want but my target is a 3:00. (3.0 rear gear, 8000 RPM &
> 27.5"
> > tire)
> >
> > Presently, I'm planning on a 3:00 rear gear with a tranny set up of 2.55
> 1st
> > gear, 1.60 2nd, 1.29 3rd. and 1.0 4th. That appears to me to be the most
> > balanced ratios to max my use of available HP. Most of the Winston Cup
> > engineers tell me taller (2.55 vs. 264) gears will help with wheel spin,
> and
> > most Drag Racers talk about using the opposite to avoid the spin.
> >
> > I would appreciate any opinion(s) regarding the problem(s) and any
> solutions.
> > Thanks in advance.
> >
> > Grib
///
/// land-speed@autox.team.net mailing list
/// To unsubscribe send a plain text message to majordomo@autox.team.net
/// with nothing in it but
///
/// unsubscribe land-speed
///
///
|