Re: [Healeys] BN2 Fan Belt

[warthodson--- via Healeys <healeys@autox.team.net>]

--===============6951969698014546495==
        boundary="----=_Part_781040_255126875.1634478210784"

------=_Part_781040_255126875.1634478210784
Content-Transfer-Encoding: quoted-printable

Bob,The way the vendors find out about an issue is if the customer tells th=
em.=C2=A0 You should forward your message to Moss.Gary Hodson


-----Original Message-----
From: Bob Spidell <bspidell@comcast.net>
To: Healeys <healeys@autox.team.net>
Sent: Sat, Oct 16, 2021 7:52 pm
Subject: [Healeys] BN2 Fan Belt

  I finally got around to fixing my loose water pump pulley and installing =
a new fan belt. I ordered a 'cogged' belt from Moss--part# 021-966--thinkin=
g it might work better than the original slab of rubber. I noticed before i=
nstalling that it was narrower than the original type that I'd had, which h=
ad rotted, but it looked like it would work. Once I started tensioning it h=
owever, it was clear it might work, but sat too low in the pulleys, and was=
 essentially riding on the bottom of the pulley grooves instead of on the s=
ides (and the angle of the sides of the belt was incorrect). Anyone else tr=
ied one of these?
=20
 I'm shocked, SHOCKED I TELL YA', that a vendor would sell something that c=
ould possibly work, but isn't truly correct.
=20
 bs
 _______________________________________________

Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archiv=
e

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys

n@aol.com


------=_Part_781040_255126875.1634478210784
Content-Transfer-Encoding: 7bit


<div style="color:black;font: 12pt Comic Sans MS, sans-serif;">Bob,
<div>The way the vendors find out about an issue is if the customer tells 
them.&nbsp; You should forward your message to Moss.</div>

<div>Gary Hodson<br>
<br>
<br>

<div style="font-family:arial,helvetica;font-size:10pt;color:black"><font 
size="2">-----Original Message-----<br>
From: Bob Spidell &lt;bspidell@comcast.net&gt;<br>
To: Healeys &lt;healeys@autox.team.net&gt;<br>
Sent: Sat, Oct 16, 2021 7:52 pm<br>
Subject: [Healeys] BN2 Fan Belt<br>
<br>

<div id="yiv8575284951">
  

    
  
  
<div>
    I finally got around to fixing my loose water pump pulley and
    installing a new fan belt. I ordered a 'cogged' belt from
    Moss--part# 021-966--thinking it might work better than the original
    slab of rubber. I noticed before installing that it was narrower
    than the original type that I'd had, which had rotted, but it looked
    like it would work. Once I started tensioning it however, it was
    clear it <i>might </i>work, but sat too low in the pulleys, and
    was essentially riding on the bottom of the pulley grooves instead
    of on the sides (and the angle of the sides of the belt was
    incorrect). Anyone else tried one of these?<br>

    <br>

    I'm shocked, SHOCKED I TELL YA', that a vendor would sell something
    that could possibly work, but isn't truly correct.<br>

    <br>

    bs<br>

  </div>


</div>
_______________________________________________<br>
<br>
Archive: <a href="http://www.team.net/pipermail/healeys"; 
target="_blank">http://www.team.net/pipermail/healeys </a><a 
href="http://autox.team.net/archive"; 
target="_blank">http://autox.team.net/archive</a><br>
<br>
<a ymailto="mailto:Healeys@autox.team.net"; 
href="mailto:Healeys@autox.team.net";>Healeys@autox.team.net</a><br>
<a href="http://autox.team.net/mailman/listinfo/healeys"; 
target="_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
<br>
</font></div>
</div>
</div>

------=_Part_781040_255126875.1634478210784--

--===============6951969698014546495==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys



--===============6951969698014546495==--