healeys
[Top] [All Lists]

[Healeys] Fwd: Luggage Rack

To: healeys@autox.team.net
Subject: [Healeys] Fwd: Luggage Rack
From: editorgary@aol.com
Date: Sun, 16 Jun 2013 15:43:26 -0400 (EDT)
Delivered-to: mharc@autox.team.net
Delivered-to: healeys@autox.team.net
References: <mailman.25.1371405604.4241.healeys@autox.team.net> <8D038E0723C55B3-348-114D4@webmail-d168.sysops.aol.com>
-----Original Message-----
From: editorgary <editorgary@aol.com>
To: healeys <healeys@autox.team.net>
Sent: Sun, Jun 16, 2013 12:40 pm
Subject: Luggage Rack


 Your biggest potential problem will be the hinges. If they are the stock
originals, they rotate on a serrated press-fit pin that can be pushed out from
the smaller diameter end, and then the large bolt is inserted in place,
fastening the luggage rack so it lifts with the boot lid. (And be sure that
you don't lose those little pins, so figure out where you'll put them for when
you want to remove the rack.)

If your hinges are, in fact, fitted with rivets, then they're the cheap
aftermarket replacements sold from some third-rate suppliers, and you will not
be able to mount the luggage rack until you buy new original-spec hinges.

As originally intended, the legs are fastened with the chrome brackets to the
bottom lip of the boot lid in such a way that the rubber legs rest on the
bumper brackets. It's a bit complicated, but does work and positions the
luggage rack parallel with the ground. However, on the roadsters, that means
you can't see over anything fastened to the rack -- but then, with the
convertible you already have that problem whenever the top is put down.

Instead of fitting as original, some of us simply have rotated the rear legs
180 degrees so that instead of going out and down, they go down then out, and
can be rested into the bumper guards, with the rack at an angle parallel to
the boot lid. The only thing you have to do then is bungee the rack to the
bumper once the luggage is put on it, so it stays stuck down into the bumper
guards.

Good luck with the hinges.

G.



Gary Anderson
Editor-at-Large
Austin-Healey Magaziner





the rack to the trunk lid. They sentme:1 trunk rack,2 rubber capped legs about
15" long,2 acorn nuts (which I think I see in the cataloge photo) threaded on
to whatamounts to be around 1/4" bolt about 1/2 " long with a smooth 1.5" long
1/8"diameter shaft coming out of the bolt head,1 strip of rubber about 5" x
1-3/4",2  hex  3/8" or 5/16" bolts about 3/4" long with hex nuts and2
partially threaded studs, each with a 2 holed paddle welded to one end, atube
clamp in the middle between a standard hex nut and a special 3/4" longhex
nut.I assume the front of the rack either mounts to the trunk hinge (but I
don'tknow how as my hinge uses what looks like a rivet) or to the paddle
endedstuds.I assume the back of the rack either just sits on the the bumper
framebrackets (which would make it scrach the paint when the lid is raised) or
usesthe paddle studs (which then forces the front of the rack to somehow mount
tothe trunk hinge). I have no guesses as to what the protruding little
smoothshafts of the acorn nut assembly are for or where to put the 5" long
strip of1-1/2" rubber.Maybe I'm missing some parts?I was planning to install
the rack today. If anyone has instructions or photosavailable, would they
please e-mail them to me?Thanks!-Dave Murphy,Dearborn MI , SEMAHC'66
BJ8------------------------------____________________________________________
___Healeys mailing
listHealeys@autox.team.nethttp://autox.team.net/mailman/listinfo/healeysEnd of
Healeys Digest, Vol 5, Issue 309***************************************
_______________________________________________
Archive: http://www.team.net/archive

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys


<Prev in Thread] Current Thread [Next in Thread>