healeys
[Top] [All Lists]
<prev [Date] next>
[Advanced]
 <prev [Thread] next>

Re: [Healeys] fitting piston/caliper seals

from [john spaur] [Permanent Link][Original]
To: "Simon Lachlan" <simon.lachlan@homecall.co.uk>
Subject: Re: [Healeys] fitting piston/caliper seals
From: john spaur <jmsdarch@sbcglobal.net>
Date: Thu, 26 Apr 2012 10:58:55 -0700
Cc: healeys@autox.team.net
Delivered-to: mharc@autox.team.net
Delivered-to: healeys@autox.team.net
Dkim-signature: v=1; a=rsa-sha256; c=relaxed/relaxed; d=sbcglobal.net; s=s1024; t=1335463181; bh=ppQg+qLzLtg9Md5TysK81Ec1ZEXCXROUY54wTsf+c2M=; h=X-Yahoo-Newman-Property:X-YMail-OSG:X-Yahoo-SMTP:Received:Message-Id:X-Mailer:Date:To:From:Subject:Cc:In-Reply-To:References:Mime-Version:Content-Type; b=Iq3w4nj1e2lcVQt10nRpPQQi+IrPpFNfd7/cfHfnevx3AjUQZoZe8FiH2mSj1YbFDSyN1Qth5tVd07v0728iLIYcg8bMm+oW13F+8mT+qrfDXA1U4mZi8265nLju+cXOw0duq5KCCXp9phiH+PjFvtt8cS+eoNYhREE+BvYDHKU=
Domainkey-signature: a=rsa-sha1; q=dns; c=nofws; s=s1024; d=sbcglobal.net; h=DKIM-Signature:X-Yahoo-Newman-Property:X-YMail-OSG:X-Yahoo-SMTP:Received:Message-Id:X-Mailer:Date:To:From:Subject:Cc:In-Reply-To:References:Mime-Version:Content-Type; b=Jsd/DPHTvilizwzs+n66/rYn/q0jknIbwEeC8WHZMfpXX5vt0skrl5WmEuIkky2vJWgDthoiQPcOCBfs9T158Q46BazAoMlMwvlXKiO3p4zqmVtH/D1MBZAgz0IkJ0jX4e9zNz+BznnMBlpTRqVQ/sItqO0DvMvxs5dyHoHClR8= ;
In-reply-to: <000901cd23ce$dba04000$92e0c000$@lachlan@homecall.co.uk>
List-archive: <http://autox.team.net/pipermail/healeys>
List-help: <mailto:healeys-request@autox.team.net?subject=help>
List-id: Austin Healey Discussion <healeys.autox.team.net>
List-post: <mailto:healeys@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/healeys>, <mailto:healeys-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/healeys>, <mailto:healeys-request@autox.team.net?subject=unsubscribe>
References: <000901cd23ce$dba04000$92e0c000$@lachlan@homecall.co.uk>
Sender: healeys-bounces@autox.team.net
I fit them to the bottom of piston then fit them to the caliper and push the piston into the bore if I recall correctly. 
John

At 06:06 PM 4/26/2012 +0100, Simon Lachlan wrote:

Hi,

Can someone kindly remind me of the proper/easiest way to fit the seals into
my MkII BT7's callipers? I'm referring to the rubber boot things that go
into the outer groove within the bore and the groove around the top of the
piston.

Likewise, don't I recall that the inner seal was slightly tapered? My new
ones are square in cross section.

Simon
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/jmsdarch@sbcglobal.net 
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation  $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys

Unsubscribe/Manage: 
http://autox.team.net/mailman/options/healeys/mharc@autox.team.net
[More with this subject...]
<Prev in Thread] Current Thread [Next in Thread>
Previous by Date:  [Healeys] fitting piston/caliper seals, john spaur
Next by Date:  [Healeys] fitting piston/caliper seals, Josef.Eckert at t-systems.com
Previous by Thread:  [Healeys] fitting piston/caliper seals, john spaur
Next by Thread:  [Healeys] fitting piston/caliper seals, Josef.Eckert at t-systems.com
Indexes:  [Date] [Thread] [Top] [All Lists]