--===============3987059968123588121==
Content-Transfer-Encoding: 7bit
--Apple-Mail-8BF039CA-935A-431D-B429-CE96F25075F0
charset=utf-8
Content-Transfer-Encoding: quoted-printable
Bob that is a hydraulic bias adjustment essentially all it does is dial back=
the pressure available to the rears.=20
Sent from my iPhone
> On May 7, 2021, at 5:03 PM, Bob Kramer <rkramer56@gmail.com> wrote:
>=20
> =EF=BB=BF
> Greg
>=20
> When we looked at it at the track the knob for the bias was way in the bac=
k on the driver shaft tunnel. I'm sure it is a smooth run from there up unde=
r the bonnet to the bias bar but maybe the cable arrangement could hold a cl=
ue. Might it hang up somehow causing the rears to change to dragging while g=
etting off and on the peddle? Running with it disconnected would tell a stor=
y.
>=20
> Bob Kramer
>=20
>=20
>> On Fri, May 7, 2021 at 3:01 PM Greg Blake via Fot <fot@autox.team.net> wr=
ote:
>>=20
>>> =EF=BB=BF
>>> Fellow racers and breakers of parts,
>>>=20
>>> =20
>>>=20
>>> This past weekend we had wonderful racing at Eagles Canyon Raceway. Own=
ership turned over a couple years ago and they have finished a multi-million=
dollar renovation of the track, it is truly amazing now. ECR has always be=
en high on my list because of its potential with the natural terrain, but th=
e lack of good construction methods had held it back since it opened. That h=
as all been corrected now and it is truly amazing=E2=80=A6well enough on tha=
t for now.
>>>=20
>>> =20
>>>=20
>>> My problem
>>>=20
>>> For the past two years I have not been able to finish a race weekend w/o=
completely destroying my rear brakes. Usually related to heat build up tha=
t manifests as a blown wheel cylinder or brake shoe linings that start crack=
ing and chuncking off the shoe causing further rapid wear. This last weeken=
d, I had a total rapid failure of the rear brakes when the right rear cylind=
er let go under hard braking from 100+ mph, I may have blown another seal in=
the drivers compartment when that happened, but will spare those details. L=
uckily, my dual masters allowed me to get the car slowed reasonably with jus=
t the front brakes. For any of you that have had this happen before, you un=
derstand that with a balance bar setup, you don=E2=80=99t end up with full b=
rakes when one end fails. The balance bar rotates significantly to the side=
that has zero resistance. In my case I=E2=80=99d estimate that I had about=
20% of my front brakes available to slow the car, like I said, interesting e=
xperience that I=E2=80=99d rather not repeat again.
>>>=20
>>> =20
>>>=20
>>> My setup
>>>=20
>>> Twin Wilwood 0.7 master cylinders with a custom balance bar. Stock fron=
t TR6 calipers and stock 9=E2=80=9D TR drums with 0.75 wheel cylinders (I=E2=
=80=99ve tried everything from 5/8 up to 7/8=E2=80=9D). I also run a hydrau=
lic proportioning valve to be able to fine tune the rear hydraulic pressure.=
I was running with the aluminum rear drums until I destroyed the linings l=
ast year in one of the incidents when the rear shoe linings cracked and brok=
e completely off allowing the shoe to cut groves into the drum linings. My r=
outine setup is to put the car on jack stands to adjust the brakes. I start=
by running the rear drum shoe adjusters in until I perceive slight drag, th=
en back off two clicks. Then I adjust the rear mechanical bias with the bal=
ance bar until I have the front and rear brakes engaging (dragging) at appro=
ximately the same point of pedal travel. I then fine tune the adjustment to=
dial back the rear bias until I can threshold brake at speed and lock the f=
ronts slightly before I lock the rears. This allows me to trail brake with c=
onfidence that I=E2=80=99m not going to swap ends because of too much rear b=
rake.
>>>=20
>>> =20
>>>=20
>>> I have used stock, portifield, and TSI drum linings all with the same re=
sults.
>>>=20
>>> =20
>>>=20
>>> I=E2=80=99m looking for a couple things from the group (no disc conversi=
on ideas please):
>>>=20
>>> What is wrong with my rear brake setup and adjustment approach?
>>> What is your setup and adjustment approach?=20
>>> Do you like the amount of rear brake you get with your approach or is it=
a compromise to keep the brakes from failing?
>>> Lastly, I hate our wheel cylinders, its is a terrible design and I think=
we have real junk on the market today. I have a theory that the sliding wh=
eel cylinder assemble is part of the root cause of my failures, along with h=
eat. The piston and seal are dealing with some severe side loading once the=
cylinder starts sliding around to do its job and I don=E2=80=99t think it i=
s up to the task, especially what we get these days. Has anyone modified th=
eir backing plates and shoes to use a modern day twin piston wheel cylinder t=
hat is bolted to the backing plate? Or has anyone ditched the TR drums all t=
ogether for another 9=E2=80=9D or 10=E2=80=9D drum backing plate and guts fr=
om another source. I=E2=80=99m open to all drum brake ideas at this point. =
I=E2=80=99m really tired of not racing because of rear brake failures.=20
>>> =20
>>>=20
>>> Sorry for the long post and thanks in advance for your ideas.=20
>>>=20
>>=20
>> Greg=20
>> _______________________________________________
>> fot@autox.team.net
>>=20
>> http://www.fot-racing.com
>>=20
>> Donate: http://www.team.net/donate.html
>> Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
>> Unsubscribe/Manage: http://autox.team.net/mailman/options/fot/rkramer56@g=
mail.com
>>=20
>>=20
--Apple-Mail-8BF039CA-935A-431D-B429-CE96F25075F0
charset=utf-8
Content-Transfer-Encoding: quoted-printable
<html><head><meta http-equiv=3D"content-type" content=3D"text/html; charset=3D=
utf-8"></head><body dir=3D"auto">Bob that is a hydraulic bias adjustment ess=
entially all it does is dial back the pressure available to the rears. =
<br><br><div dir=3D"ltr">Sent from my iPhone</div><div dir=3D"ltr"><br><bloc=
kquote type=3D"cite">On May 7, 2021, at 5:03 PM, Bob Kramer <rkramer56@gm=
ail.com> wrote:<br><br></blockquote></div><blockquote type=3D"cite"><div d=
ir=3D"ltr">=EF=BB=BF<div dir=3D"ltr">Greg<div><br></div><div>When we looked a=
t it at the track the knob for the bias was way in the back on the driver sh=
aft tunnel. I'm sure it is a smooth run from there up under the bonnet to th=
e bias bar but maybe the cable arrangement could hold a clue. Might it hang&=
nbsp;up somehow causing the rears to change to dragging while getting o=
ff and on the peddle? Running with it disconnected would tell a story.</div>=
<div><br clear=3D"all"><div><div dir=3D"ltr" class=3D"gmail_signature" data-=
smartmail=3D"gmail_signature"><div dir=3D"ltr">Bob Kramer</div></div></div><=
br></div></div><br><div class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmai=
l_attr">On Fri, May 7, 2021 at 3:01 PM Greg Blake via Fot <<a href=3D"mai=
lto:fot@autox.team.net">fot@autox.team.net</a>> wrote:<br></div><blockquo=
te class=3D"gmail_quote" style=3D"margin:0px 0px 0px 0.8ex;border-left:1px s=
olid rgb(204,204,204);padding-left:1ex"><div dir=3D"auto"><br><blockquote ty=
pe=3D"cite"><div dir=3D"ltr">=EF=BB=BF
<div>
<p class=3D"MsoNormal">Fellow racers and breakers of parts,<u></u><u></u></p=
>
<p class=3D"MsoNormal"><u></u> <u></u></p>
<p class=3D"MsoNormal">This past weekend we had wonderful racing at Eagles C=
anyon Raceway. Ownership turned over a couple years ago and they have f=
inished a multi-million dollar renovation of the track, it is truly amazing n=
ow. ECR has always been high on my
list because of its potential with the natural terrain, but the lack of goo=
d construction methods had held it back since it opened. That has all b=
een corrected now and it is truly amazing=E2=80=A6well enough on that for no=
w.<u></u><u></u></p>
<p class=3D"MsoNormal"><u></u> <u></u></p>
<p class=3D"MsoNormal"><b>My problem<u></u><u></u></b></p>
<p class=3D"MsoNormal">For the past two years I have not been able to finish=
a race weekend w/o completely destroying my rear brakes. Usually rela=
ted to heat build up that manifests as a blown wheel cylinder or brake shoe l=
inings that start cracking and chuncking
off the shoe causing further rapid wear. This last weekend, I had a t=
otal rapid failure of the rear brakes when the right rear cylinder let go un=
der hard braking from 100+ mph, I may have blown another seal in the drivers=
compartment when that happened, but
will spare those details. Luckily, my dual masters allowed me to get t=
he car slowed reasonably with just the front brakes. For any of you th=
at have had this happen before, you understand that with a balance bar setup=
, you don=E2=80=99t end up with full brakes when
one end fails. The balance bar rotates significantly to the side that=
has zero resistance. In my case I=E2=80=99d estimate that I had about=
20% of my front brakes available to slow the car, like I said, interesting e=
xperience that I=E2=80=99d rather not repeat again.<u></u><u></u></p>
<p class=3D"MsoNormal"><u></u> <u></u></p>
<p class=3D"MsoNormal"><b>My setup<u></u><u></u></b></p>
<p class=3D"MsoNormal">Twin Wilwood 0.7 master cylinders with a custom balan=
ce bar. Stock front TR6 calipers and stock 9=E2=80=9D TR drums with 0.=
75 wheel cylinders (I=E2=80=99ve tried everything from 5/8 up to 7/8=E2=80=9D=
). I also run a hydraulic proportioning valve to be able to
fine tune the rear hydraulic pressure. I was running with the aluminu=
m rear drums until I destroyed the linings last year in one of the incidents=
when the rear shoe linings cracked and broke completely off allowing the sh=
oe to cut groves into the drum linings.
My routine setup is to put the car on jack stands to adjust the brakes.&nbs=
p; I start by running the rear drum shoe adjusters in until I perceive sligh=
t drag, then back off two clicks. Then I adjust the rear mechanical bi=
as with the balance bar until I have the
front and rear brakes engaging (dragging) at approximately the same point o=
f pedal travel. I then fine tune the adjustment to dial back the rear b=
ias until I can threshold brake at speed and lock the fronts slightly before=
I lock the rears. This allows me
to trail brake with confidence that I=E2=80=99m not going to swap ends beca=
use of too much rear brake.
<u></u><u></u></p>
<p class=3D"MsoNormal"><u></u> <u></u></p>
<p class=3D"MsoNormal">I have used stock, portifield, and TSI drum linings a=
ll with the same results.<u></u><u></u></p>
<p class=3D"MsoNormal"><u></u> <u></u></p>
<p class=3D"MsoNormal">I=E2=80=99m looking for a couple things from the grou=
p (no disc conversion ideas please):<u></u><u></u></p>
<ol style=3D"margin-top:0in" start=3D"1" type=3D"1">
<li style=3D"margin-left:2.25pt">What is wrong with my rear brake setup and a=
djustment approach?<u></u><u></u></li><li style=3D"margin-left:2.25pt">What i=
s your setup and adjustment approach?
<u></u><u></u></li><li style=3D"margin-left:2.25pt">Do you like the amount o=
f rear brake you get with your approach or is it a compromise to keep the br=
akes from failing?<u></u><u></u></li><li style=3D"margin-left:2.25pt">Lastly=
, I hate our wheel cylinders, its is a terrible design and I think we have r=
eal junk on the market today. I have a theory that the sliding wheel c=
ylinder assemble is part
of the root cause of my failures, along with heat. The piston and sea=
l are dealing with some severe side loading once the cylinder starts sliding=
around to do its job and I don=E2=80=99t think it is up to the task, especi=
ally what we get these days. Has anyone modified
their backing plates and shoes to use a modern day twin piston wheel cylind=
er that is bolted to the backing plate? Or has anyone ditched the TR d=
rums all together for another 9=E2=80=9D or 10=E2=80=9D drum backing plate a=
nd guts from another source. I=E2=80=99m open to all drum
brake ideas at this point. I=E2=80=99m really tired of not racing bec=
ause of rear brake failures.
<u></u><u></u></li></ol>
<p class=3D"MsoNormal"><u></u> <u></u></p>
<p class=3D"MsoNormal">Sorry for the long post and thanks in advance for you=
r ideas. </p></div>
</div></blockquote><br><div>Greg </div></div>__________________________=
_____________________<br>
<a href=3D"mailto:fot@autox.team.net"; target=3D"_blank">fot@autox.team.net</=
a><br>
<br>
<a href=3D"http://www.fot-racing.com"; rel=3D"noreferrer" target=3D"_blank">h=
ttp://www.fot-racing.com</a><br>
<br>
t=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://autox.team.net/archive"; rel=3D"noreferrer" target=
=3D"_blank">http://autox.team.net/archive</a> <a href=3D"http://www.team.net=
/pipermail/fotUnsubscribe/Manage" rel=3D"noreferrer" target=3D"_blank">http:=
//www.team.net/pipermail/fot<br>
/rkramer56@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox.team=
.net/mailman/options/fot/rkramer56@gmail.com</a><br>
<br>
<br>
</blockquote></div>
</div></blockquote></body></html>=
--Apple-Mail-8BF039CA-935A-431D-B429-CE96F25075F0--
--===============3987059968123588121==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
--===============3987059968123588121==--
|