What Steve said, this is the way to do it.
Also I recently noticed that Moss is selling a double bearing gear now.
Glen
-----Original Message-----
From: Steve Yott <tr4 at wi.rr.com>
To: van.mulders.marcel <van.mulders.marcel at telenet.be>; 'fubog1' <fubog1 at
aol.com>
Sent: Mon, Jan 8, 2018 7:01 pm
Subject: RE: [Fot] TR6 transmission rebuild - counter shaft gears
For all gearboxes I rebuild and for a number of other builders I modify the lay
gear by boring the 1st gear end in order to fit a double bearing which pretty
much eliminates bearing and shaft failure. There is too much load on the
bearing and shaft in this area and the double bearing installation mimics the
more durable Stag gearbox. At the same time I machine a groove in the end to
fit a circlip to prevent bearing walk. I also use Loctite retaining compound
to add a little further fixing for the bearings.
Steve Yott
Silver Lake Triumph Centre
From: Fot [mailto:fot-bounces at autox.team.net] On Behalf Of
van.mulders.marcel--- via Fot
Sent: Monday, January 08, 2018 12:20 PM
To: fubog1 <fubog1 at aol.com>
Cc: fot <fot at autox.team.net>
Subject: Re: [Fot] TR6 transmission rebuild - counter shaft gears
These shell needle bearings are easily damaged : when the shell is warped a
bit, it will fail. When the bearing is in place, one should check if the
needles can be spinned freely.
A nylaton bush of the TR4a -TR6 inner wishbone bearing is great for pushing
these shell bearings in place. These bearings are not secured by a circlip,
contrary to the open cage needle bearings.
But the needles of the open cage bearings are running directly against the ev.
worn or damaged inner surface of the laygear.
Marcel
Van: "fot" <fot at autox.team.net>
Aan: gblake58tr3 at icloud.com, "fot" <fot at autox.team.net>
Verzonden: Maandag 8 januari 2018 15:33:33
Onderwerp: Re: [Fot] TR6 transmission rebuild - counter shaft gears
It probably has the later type shell bearings and 1 or both have worked loose
in the laygear housing bore and "milled" into the thrust washer (s).
Glen
-----Original Message-----
From: Greg Blake via Fot <fot at autox.team.net>
To: Fot <fot at autox.team.net>
Sent: Sun, Jan 7, 2018 8:56 pm
Subject: [Fot] TR6 transmission rebuild - counter shaft gears
I am rebuilding a TR6 transmission and ran into a strange snag. When I removed
the countershaft the counter shaft gears did not drop to the bottom of the
case. I had to tap on the counter shaft gear set with a brass punch to get them
to move far enough to allow the input shaft and gear to be removed. Now that I
have the main shaft out of the case, I can't get the counter shaft gears out of
the case. I've been able to move them a little bit by tapping on the gears with
a brass punch through the drain hole but I can't get them out. Has anyone run
into this before? Any ideas to get them out?
Thanks.
Greg
Sent from my iPhone
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
_______________________________________________
fot at autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/fot/attachments/20180109/dafe019b/attachment.html>
|