Funny that I received about an hour ago a new set of AE .020 pistons that I
had ordered. They are made by NURAL in Poland which is a subsidiary of
Federal Mogul. They look very nice in quality and are fitted with Goetze
rings which look ok but they have the one piece oil control ring which I
have never been crazy about. I prefer the Grant type 3 piece oil ring but
these are easier to install!
Steve Yott
-----Original Message-----
From: fot-bounces@autox.team.net [mailto:fot-bounces@autox.team.net] On
Behalf Of Glenn Franco
Sent: Friday, January 11, 2013 4:41 PM
To: Body Wagner
Cc: spitfires@autox.team.net; Doug Braun; 6pack@autox.team.net; Friends of
triumph
Subject: Re: [Fot] [Spits] County Pistons Quality Control Issue
The new defective TR6 set I just installed are made in Taiwan.
I just looked in my collection of NOS ones and I have 4 new .020" Spit
County Pistons and those appear to be made in the UK but they are likely
10-15 yrs old or better.
Glenn
On 1/11/2013 5:19 PM, Body Wagner wrote:
> Where are AE pistons made?
>
> Boyd C Wagner
>
> Sent from my iPad
>
> On Jan 11, 2013, at 5:01 PM, Glenn Franco <gaf3@charter.net> wrote:
>
>> Yes the County Rockers are made in India.
>> They usually have better quality control than most.
>>
>> On 1/11/2013 4:33 PM, Doug Braun wrote:
>>> Another horror story:
>>>
>>> A while back I replaced my Spit's rocker arm shaft with the part
>>> that most vendors sold. I believe it was "County"
>>> branded, and it was made in India. I went to adjust the valves a
>>> few days later, and I noticed that the front four rocker arms seemed
>>> rather oil-starved. When I ran the engine with the rocker arm cover
>>> off, I could see that only the rear four rocker arms were getting
>>> lubricated.
>>> It turned out that the shaft was not completely hollow: They had
>>> rifle-drilled it inwards from each end, but they did not drill deep
>>> enough, and the two holes did not meet up in the center.
>>>
>>> Doug
>>>
>>>
>>> On Fri, Jan 11, 2013 at 4:14 PM, Glenn Franco <gaf3@charter.net
>>>
>>> FYI
>>> I am in the midst of a TR6 Rebuild with an engine that is .020"
>>> overbored.
>>> While fitting up the pistons and checking clearances everything
>>> checked out and the bore was concentric and to specs.
>>> With the piston installed in the bore I noticed increased drag
>>> with #1 piston installed.
>>> With rings gaps, skirt clearance correct I pulled the piston and
>>> didn't see any issues.
>>> Further inspection showed that the piston was cocked in the bore
>>> and had score marks on the bottom of one skirt with the same wear
>>> just below the oil ring on the other side.
>>> After inspecting it with the machine shop we noticed that the ring
>>> grooves were not fully machined on one side of the piston.
>>> The rings would not move far enough in the groove and was proud of
>>> the surface causing the piston to cock in the bore.
>>> We collectively have not seen this before and have a new set of AE
>>> pistons not County on the way.
>>>
>>> Having spent many years in Automotive Engineering at one of the
>>> former Big Three, these events are usually not one of's.
>>> There likely are many more out there that ran down the line in the
>>> same batch at the same time before it was caught.
>>>
>>> These are new County Piston sets (I think made in Israel now).
>>> I would inspect their parts very closely before you install them.
>>>
>>> I also noticed machine chips in the machined groove of their
>>> Tri-Metal Main Bearings (Israel).
>>> The chips were in the machined groove and were plated over with
>>> the babbit and copper.
>>>
>>> I have had very good experiences with their parts in the past.
>>> Just thought I would provide a heads up.
>>>
>>> Glenn
>>> _______________________________________________
>>>
>>> Donate: http://www.team.net/donate.html
>>> Suggested annual donation $11.47
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> Unsubscribe/Manage:
>>>
>>> http://autox.team.net/mailman/options/spitfires/doug@dougbraun.com
>> _______________________________________________
>> fot@autox.team.net
>>
>> http://www.fot-racing.com
>>
>> Donate: http://www.team.net/donate.html
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe:
>> http://autox.team.net/mailman/options/fot/boydwagner3@aol.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/fot/tr4@wi.rr.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/fot/mharc@autox.team.net
|