Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TR\]\s+Removing\s+Front\s+Grease\s+Caps\/GT6\?\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[TR\]\s+Removing\s+Front\s+Grease\s+Caps\/GT6\?\s*$/: 8 ]

Total 8 documents matching your query.

1. [TR] Removing Front Grease Caps/GT6? (score: 1): Author: "Martin Secrest" <moira.secrest@verizon.net>; Date: Sat, 26 Feb 2011 10:37:37 -0500; John, Very funny! We also attended a concert of UK origin but with much better music I am sure. We saw "Rain" and had a great time. No one left early I am sure and if the older gent with the walking; /html/triumphs/2011-02/msg00278.html (6,492 bytes)
2. Re: [TR] Removing Front Grease Caps/GT6? (score: 1): Author: "Martin Secrest" <moira.secrest@verizon.net>; Date: Sat, 26 Feb 2011 12:22:58 -0500; Hi Frank & list! On my TR4A, the zerks are NOT on or in the trunnions but in the vertical li= nk = with a hole drilled down the center to the insert of the zerk is. You oil = through the zerk & it tr; /html/triumphs/2011-02/msg00279.html (8,505 bytes)
3. Re: [TR] Removing Front Grease Caps/GT6? (score: 1): Author: "Gary Klein" <tr6.guy@verizon.net>; Date: Sun, 27 Feb 2011 08:31:01 -0500; Randall wrote: Yup, the 4A uses the same design as the TR5/250/6.=A0 Earlier TRs (like the one Frank is working on) were different, though. -- Randall=A0 -- OK so now I know the TR3's are different t; /html/triumphs/2011-02/msg00281.html (7,652 bytes)
4. Re: [TR] Removing Front Grease Caps/GT6? (score: 1): Author: Geo Hahn <ahwahneetr@gmail.com>; Date: Sun, 27 Feb 2011 10:15:08 -0700; I have a set of front and rear Goodparts springs for TR4a-TR6 I'd like to sell. They list for $89/pair. I'll sell for $100 for all four plus shipping. Thanks, Dan Forgey _____________________________; /html/triumphs/2011-03/msg00001.html (7,537 bytes)
5. [TR] Removing Front Grease Caps/GT6? (score: 1): Author: moira.secrest at verizon.net (Martin Secrest); Date: Sat, 26 Feb 2011 10:37:37 -0500; It's been so long since I did this I forget the tutorial and getting the caps off the front hubs without damage. I replaced the bearings and they need adjusting. Oof. -- Martin Secrest 73 GT6 72 TR6; /html/triumphs/2011-02/msg00554.html (7,710 bytes)
6. [TR] Removing Front Grease Caps/GT6? (score: 1): Author: moira.secrest at verizon.net (Martin Secrest); Date: Sat, 26 Feb 2011 12:22:58 -0500; Thanks folks .. the right toothy channel lock on the lip got them off. Harder than I remember it being, but they went back in gently ...; /html/triumphs/2011-02/msg00555.html (9,882 bytes)
7. [TR] Removing Front Grease Caps/GT6? (score: 1): Author: tr6.guy at verizon.net (Gary Klein); Date: Sun, 27 Feb 2011 08:31:01 -0500; Martin, Here's a better technique that won't mark up the cap. It works on my TR6 and TR8 so I suspect it will work on the GT6. Screw in a #10 bolt into the hole of the cap, about a 1" or so long bolt; /html/triumphs/2011-02/msg00557.html (8,188 bytes)
8. [TR] Removing Front Grease Caps/GT6? (score: 1): Author: ahwahneetr at gmail.com (Geo Hahn); Date: Sun, 27 Feb 2011 10:15:08 -0700; And if you use an eye bolt (about 2" long) you can do this w/o a wrench, just turn the screw eye by hand (unless the cap it rusted or otherwise stuck). Geo; /html/triumphs/2011-02/msg00561.html (8,180 bytes)

Current List: 1 - 8
Page: [1]