Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*exhausting\s+weekend\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*exhausting\s+weekend\s*$/: 7 ]

Total 7 documents matching your query.

1. exhausting weekend (score: 1): Author: thompson@ridgeback.East.Sun.COM (Keith B. Thompson - Sun); Date: Tue, 26 Sep 1995 15:17:50 -0400; hi, friday my new ss exhaust system arrived and over the week end i took a chance in trying to install it into my 250. (my original plan was to drive it to my local garage and let them do it). my con; /html/triumphs/1995-09/msg00504.html (7,885 bytes)
2. Re: exhausting weekend (score: 1): Author: Joe Flake <flake@a3115jmf.atl.hp.com>; Date: Wed, 27 Sep 1995 09:21:51 -0500 (EDT); Say dirty words, leave the car, and go have a cold beverage of your choice! Seriously, that's an excellent path to take when major setbacks occur in the middle of a project. When you're in a better s; /html/triumphs/1995-09/msg00514.html (9,092 bytes)
3. Re: exhausting weekend (score: 1): Author: Andrew Mace <amace@unix2.nysed.gov>; Date: Wed, 27 Sep 1995 09:52:24 -0900 (PDT); Frankly, I think your best bet would be to remove the exhaust manifold from the engine. Then, anyone with an oxy/acetylene torch should be able to heat the flange enough to enable the stud to be remo; /html/triumphs/1995-09/msg00515.html (8,529 bytes)
4. Exhausting Weekend (score: 1): Author: rvince00@counsel.com (Ross Vincente -- TransAmer. Financial - Los Angeles ); Date: Wed, 27 Sep 95 12:03:38 EDT; To: Triumph Mail List, Triumph Subscribers Inet Okay, I'll throw in my two cents now, after having lived through the restoration from Hell (68 Datsun 1600 Roadster - frame off, rust everywhere, broke; /html/triumphs/1995-09/msg00520.html (8,654 bytes)
5. Re: exhausting weekend (score: 1): Author: Greg Meboe <meboe@wsunix.wsu.edu>; Date: Fri, 29 Sep 1995 12:25:57 -0700 (PDT); Keith, I've had good luck removing broken studs from exhaust manifolds with this method (assuming there is at least 1/4 inch sticking out). The reason the studs seize in the manifold is due to rust o; /html/triumphs/1995-09/msg00598.html (8,661 bytes)
6. Re: exhausting weekend (score: 1): Author: "Chris Kantarjiev" <cak@godzilla.studio.sgi.com>; Date: Fri, 29 Sep 1995 14:16:10 -0700 "Re: exhausting weekend" (Sep 29, 12:25pm); I seem to write this up about once a year; maybe one of these times I'll remember to save it. I looked, but can't find it on the SOL tech tips web page...I've used the methods described below on exha; /html/triumphs/1995-09/msg00602.html (11,931 bytes)
7. Re: exhausting weekend (score: 1): Author: "Chris Boston" <cboston@zeu.tt.umist.ac.uk>; Date: Mon, 2 Oct 1995 10:59:07 +0000 "Re: exhausting weekend" (Sep 29, 12:25pm); Morning folks, I've been following this thread with some interest, since I have had a blown gasket (manifold to down-pipe) for a while, and the noise has been geting worse. I finally plucked up the c; /html/triumphs/1995-10/msg00017.html (8,671 bytes)

Current List: 1 - 7
Page: [1]