Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Valve\s+cover\s+gasket\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Valve\s+cover\s+gasket\s*$/: 7 ]

Total 7 documents matching your query.

1. Valve cover gasket (score: 1): Author: Elliott DeGraff <degraff@erols.com>; Date: Fri, 24 Dec 1999 21:26:33 -0500; I am going to replace the valve cover gasket on my 71B. I dimly recall advice to soak the gasket in water before installing it. Any ideas on time, temperature or any other conditions to assure a leak; /html/mgs/1999-12/msg01099.html (6,506 bytes)
2. Re: Valve cover gasket (score: 1): Author: Barney Gaylord <barneymg@ntsource.com>; Date: Sat, 25 Dec 1999 02:03:14; it. Any ideas .... to assure a leak free installation? Yes, forget the water. The primary concern is that the valve cover has to be flat along the bottom edge to make the gasket seal on the head. Sta; /html/mgs/1999-12/msg01103.html (9,167 bytes)
3. Re: Valve cover gasket (score: 1): Author: Elliott DeGraff <degraff@erols.com>; Date: Wed, 29 Dec 1999 11:15:25 -0500; Many thanks to Barney and Valerie for your advice on installing the new gasket leak free. Now if only I can convince my wife to let me use the kitchen counter as a work bench:-) After all, it is her; /html/mgs/1999-12/msg01235.html (10,083 bytes)
4. Valve cover gasket (score: 1): Author: Miles E Vaughan <edvaughan@juno.com>; Date: Tue, 7 Sep 1999 19:34:21 -0500; Hello All, this may be a dumb question, but I am putting a new valve cover gasket on my B. My hanes just says "refit the rocker cover...". But do I need to put any RTV stuff on the gasket at certains; /html/mgs/1999-09/msg00321.html (6,920 bytes)
5. Re: Valve cover gasket (score: 1): Author: "mowog77 bootknocker" <mowog77@theglobe.com>; Date: Wed, 08 Sep 1999 05:49:12 -0700; No, don't use Permatex on the valve cover gasket, it is not needed and will only glob out from underneath making the motor look like it had been in a two-bit shop. Use a cork gasket and make sure you; /html/mgs/1999-09/msg00339.html (7,725 bytes)
6. Re: Valve cover gasket (score: 1): Author: Larry Colen <lrcar@red4est.com>; Date: Wed, 8 Sep 1999 11:23:21 -0700; I had a bitch of a time getting my valve cover gasket to seal. I learned two tricks in the process: 1) pre soak the cork gasket in oil. 2) A permatex goo called "the right stuff. I glued the gasket t; /html/mgs/1999-09/msg00361.html (7,901 bytes)
7. Re: Valve cover gasket (score: 1): Author: "Paul Hunt" <paul.hunt1@virgin.net>; Date: Thu, 9 Sep 1999 19:52:44 +0100; The rocker cover fixing includes two rubber washers that live under the dished washers. These compress and harden over time, but are onlly a few pence each (two-off) to replace. PaulH. http://freespa; /html/mgs/1999-09/msg00442.html (7,793 bytes)

Current List: 1 - 7
Page: [1]