- 1. TD Clutch Cable VS Clutch Levers (score: 1)
- Author: BobMGT@aol.com
- Date: Mon, 1 May 2000 23:49:37 EDT
- The clutch lever linkage on my TD is loose as a goose. The bush and clevis pin holes are worn out. I could get a new bush and have the holes welded and re-drilled. But it looks like it would be easie
- /html/mg-t/2000-05/msg00000.html (7,296 bytes)
- 2. Re: TD Clutch Cable VS Clutch Levers (score: 1)
- Author: Bob Howard <mgbob@juno.com>
- Date: Tue, 2 May 2000 16:16:32 -0400
- I went through the work of filling and milling all the holes to fit the new clevis pins that I got from Moss. They were hardened pins, by the way, much harder metal than the originals. There was sti
- /html/mg-t/2000-05/msg00001.html (9,413 bytes)
- 3. Re: TD Clutch Cable VS Clutch Levers (score: 1)
- Author: BobMGT@aol.com
- Date: Tue, 2 May 2000 22:14:39 EDT
- Bob: I'm also at a loss, there is nothing on my TD that I would describe as a stop-clutch pedal. Bob Donahue (Still stuck in the '50s) EMAIL - BOBMGT@AOL.COM 52 MGTD - under DIY restoration NEMGTR #1
- /html/mg-t/2000-05/msg00004.html (7,864 bytes)
- 4. Re: TD Clutch Cable VS Clutch Levers (score: 1)
- Author: Bullwinkle <yd3@nvc.net>
- Date: Wed, 03 May 2000 00:09:23 -0700
- Crawled under TD 25939, looked at the brake box, and stuck my finger into the big hole in the bottom. The stop feels (it can't be "appears" as I cannot see it) to be a shouldered pin about 3/4 in dia
- /html/mg-t/2000-05/msg00005.html (7,669 bytes)
- 5. Re: TD Clutch Cable VS Clutch Levers (score: 1)
- Author: "david.tinker" <david.tinker@virgin.net>
- Date: Wed, 3 May 2000 12:00:46 +0100
- You can install a clutch pedal stop without taking up the floor boards, there is a side access panel on the pedal box and can be removed by removing 4 screws. If anyone wants the dimensions of the pe
- /html/mg-t/2000-05/msg00006.html (7,684 bytes)
- 6. Fw: TD Clutch Cable VS Clutch Levers (score: 1)
- Author: "david.tinker" <david.tinker@virgin.net>
- Date: Wed, 3 May 2000 12:03:35 +0100
- removing
- /html/mg-t/2000-05/msg00007.html (7,945 bytes)
- 7. Re: TD Clutch Cable VS Clutch Levers (score: 1)
- Author: "Bob and Carolyn Grunau" <cgrunau@pathcom.com>
- Date: Wed, 3 May 2000 07:28:09 -0400
- The stop-clutch pedal is located inside the pedal box on a LHD car. It is at the rear of the box, near the inner wall and box cover. It is a small round bar piece, ( approx. 5/8" diameter ), and is a
- /html/mg-t/2000-05/msg00008.html (9,367 bytes)
This search system is powered by
Namazu