Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Doin\'\s+it\s+today\!\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*Doin\'\s+it\s+today\!\s*$/: 8 ]

Total 8 documents matching your query.

1. Doin' it today! (score: 1): Author: "John & Allison Cyganowski" <janah@att.net>; Date: Sun, 15 May 2005 12:09:37 -0400; Okay, I am pulling my tranny today. I have the carpets, dash support removed and the passenger seat pulled. I have heard that you can pull the tranny-overdrive up and out through the passenger side.; /html/6pack/2005-05/msg00191.html (7,329 bytes)
2. RE: Doin' it today! (score: 1): Author: "Shawn J. Loseke" <sloseke@holly.colostate.edu>; Date: Sun, 15 May 2005 10:28:25 -0600; Really the easiest way to do it. Don't be afraid. :o) Less than 100lbs? I don't have overdrive so I'm guessing there. You won't need to lift the whole weight until you lift it our of the car. High e; /html/6pack/2005-05/msg00192.html (8,336 bytes)
3. RE: Doin' it today! (score: 1): Author: "Navarrette, Vance" <vance.navarrette@intel.com>; Date: Sun, 15 May 2005 09:55:30 -0700; a) Yes, it works just fine to pull it out through the passenger side. Getting it in is more of a challenge, but can be done by one person. b) 100 lbs. (77lbs w/o the OD) c) Doesn't matter. Just make; /html/6pack/2005-05/msg00193.html (8,080 bytes)
4. RE: Doin' it today! (score: 1): Author: Peter Zaborski <plz@shaw.ca>; Date: Sun, 15 May 2005 11:29:09 -0600; John, one tip...remove the driver's seat as well. It's only 2 bolts and you will have more room to play with in the car. Especially since it sounds like this is the first time you are doing this. It; /html/6pack/2005-05/msg00195.html (7,707 bytes)
5. Re: Doin' it today! (score: 1): Author: Greg Perry <rgperry@earthlink.net>; Date: Sun, 15 May 2005 12:40:06 -0500 (GMT-05:00); Yes, I also remove the drivers seat. not sure exactly, probably 125 to 150 lbs Enough for you to fit inorder to remove the lower belhousng bolts and clutch slave cylinder. boredom, lack of free ente; /html/6pack/2005-05/msg00196.html (7,984 bytes)
6. Re:Doin' it today! (score: 1): Author: "John & Allison Cyganowski" <janah@att.net>; Date: Sun, 15 May 2005 22:02:21 -0400; Thanks for the replies and encouragement. I think I made decent progress today. I have the upper bell housing bolts to remove and I think it should come out. Lessons: a.) Starter? I wasn't planning; /html/6pack/2005-05/msg00200.html (8,311 bytes)
7. RE: Doin' it today! (score: 1): Author: "Navarrette, Vance" <vance.navarrette@intel.com>; Date: Mon, 16 May 2005 07:53:10 -0700; Dead body? Hah! That is merely an impropriety, like getting caught making out with your cousin. My dead body was that the fork pin had sheared, and rather than fix it, my DPO welded the fork to the c; /html/6pack/2005-05/msg00205.html (8,715 bytes)
8. RE: Doin' it today! (score: 1): Author: "Navarrette, Vance" <vance.navarrette@intel.com>; Date: Tue, 17 May 2005 09:47:19 -0700; Dead body? Hah! That is merely an impropriety, like getting caught making out with your cousin. My dead body was that the fork pin had sheared, and rather than fix it, my DPO welded the fork to the c; /html/6pack/2005-05/msg00219.html (8,679 bytes)

Current List: 1 - 8
Page: [1]