Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Land\-speed\]\s+Not\s+LSR\s+Question\,\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Land\-speed\]\s+Not\s+LSR\s+Question\,\s*$/: 9 ]

Total 9 documents matching your query.

1. [Land-speed] Not LSR Question, (score: 1): Author: Dale Krumheuer <dmirror3@yahoo.com>; Date: Mon, 18 Jun 2007 13:25:28 -0700 (PDT); This sounds so eay yet I don't want to buy the wrong size steel rod stock (again). I need to cut thread to fit 3/8" 16. I blundered and bought 3/8 inch stock yet its obviously too large for my die. W; /html/land-speed/2007-06/msg00143.html (7,906 bytes)
2. Re: [Land-speed] Not LSR Question, (score: 1): Author: "Ed Weldon" <23.weldon@comcast.net>; Date: Mon, 18 Jun 2007 15:20:32 -0700; Dale--there are several possibilities here. But let me step you through the way I have put coarse threads on 3/8, 7/16 and 1/2" diameter rod when only simple tools are at hand. First take the rod to; /html/land-speed/2007-06/msg00144.html (10,741 bytes)
3. Re: [Land-speed] Not LSR Question, (score: 1): Author: "Rich Fox" <v4gr@rcn.com>; Date: Mon, 18 Jun 2007 15:28:03 -0700; Without grabing my Machinery handbook I can say that the major diameter of a 3/8-16 bolt is about .370. Very close to 3/8. Not sure what is going on.. -- Original Message -- From: "Dale Krumheuer" <d; /html/land-speed/2007-06/msg00145.html (8,397 bytes)
4. Re: [Land-speed] Not LSR Question, (score: 1): Author: Skip Higginbotham <saltrat@pahrump.com>; Date: Mon, 18 Jun 2007 18:29:30 -0700; Might try buying 3/8 threaded steel rod and cut it off??? _______________________________________________ Land-speed mailing list http://autox.team.net/mailman/listinfo/land-speed; /html/land-speed/2007-06/msg00146.html (8,954 bytes)
5. Re: [Land-speed] Not LSR Question, (score: 1): Author: "Glen Barrett" <speedtimer@beyondbb.com>; Date: Mon, 18 Jun 2007 19:35:21 -0600; I have never had a problem threading standard rod sizes. just add a starting taper and go slow and make sure it's cutting straight. Glen -- Original Message -- From: "Skip Higginbotham" <saltrat@pahr; /html/land-speed/2007-06/msg00147.html (8,105 bytes)
6. Re: [Land-speed] Not LSR Question, (score: 1): Author: <neil@dbelltech.com>; Date: Mon, 18 Jun 2007 19:03:03 -0700; I think you've pointed out one of the problems; a 3/8-16 bolt thread is not 0.375" major diameter. That would be 100% thread and that would be next to impossible to mate with a nut at maximum spec t; /html/land-speed/2007-06/msg00148.html (9,086 bytes)
7. Re: [Land-speed] Not LSR Question, (score: 1): Author: "don thigpen" <piggy@accessatc.net>; Date: Mon, 18 Jun 2007 23:20:10 -0400; a 3/8 bolt thread does have a major diameter of .375 , unless of course you have a very low class of fit and even then it is speced at .375 and the nut is speced accordingly . please dont put a bolt; /html/land-speed/2007-06/msg00149.html (8,241 bytes)
8. Re: [Land-speed] Not LSR Question, (score: 1): Author: "don thigpen" <piggy@accessatc.net>; Date: Mon, 18 Jun 2007 23:27:05 -0400; just a little background on threading my threading test at machinists school had me make one each bolt in 1/4,3/8,1/2 and 7/16 and the nuts to fit them on the lathe . the bolt had to be the right len; /html/land-speed/2007-06/msg00150.html (8,396 bytes)
9. Re: [Land-speed] Not LSR Question, (score: 1): Author: "Rich Fox" <v4gr@rcn.com>; Date: Mon, 18 Jun 2007 21:05:34 -0700; Yeah that's what it says in the Machinist's Practical Guide. But pull a head bolt from a Small block Ford and see if it's really .4375. The one I tried wasn't Chrysler rod bolt--.373. Life is sometim; /html/land-speed/2007-06/msg00151.html (8,476 bytes)

Current List: 1 - 9
Page: [1]