- 41. Re: shield gas for MIG (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Mon, 18 May 1998 16:40:44 -0400
- straight Patch They (sales people at the welding supply house) told me that for mild steel (like all the body parts of a car) it is best to use a 75/25 % mix of Argon and CO2. If you are trying to do
- /html/shop-talk/1998-05/msg00072.html (7,816 bytes)
- 42. Fwd: Re: shield gas for MIG (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 19 May 1998 10:07:14 -0400
- CORRECTION: Make that straight Argon for Aluminum Sorry, Nils
- /html/shop-talk/1998-05/msg00077.html (7,531 bytes)
- 43. Re: shield gas for MIG (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Wed, 20 May 1998 17:24:50 -0400
- Thank you very much Bill ! Very informative, you seem to be a storehouse of information on the subject. I am about to weld up a roll cage for my car I am using DOM SAE1010 or 1020 steel tubing that i
- /html/shop-talk/1998-05/msg00080.html (9,326 bytes)
- 44. Re: R134 licensing (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Wed, 27 May 1998 17:48:58 -0400
- As far as I know, you need no license at all! Just walk down to your local PEP Boys and buy all the 134A that you want. Regards Nils Yardley, PA 59(100-6) 69XKE 72/73MGB 52MGTD
- /html/shop-talk/1998-05/msg00118.html (6,856 bytes)
- 45. Re: Parts Washer Warning (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Thu, 09 Apr 1998 12:54:25 -0400
- I have noticed that many of you on the list have complaints about parts washers and solvents to use in them. I have had the same problem over the years and have tried all kinds of solvents that smell
- /html/shop-talk/1998-04/msg00029.html (8,072 bytes)
- 46. Re: Parts Washer Solvent (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Thu, 09 Apr 1998 15:09:16 -0400
- You use the stuff straight out of the can. I admit it is a little on the expensive side, but then I only have a 3 gallon washer. (I only have a 20 gallon one in my dreams) I must admit I did not thin
- /html/shop-talk/1998-04/msg00030.html (7,636 bytes)
- 47. Shop Tools (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Wed, 15 Apr 1998 15:23:47 -0400
- So afraid I was going to owe the IRS this year. So I made large quarterly payments and just did my taxes and am actually getting some small fraction of my money back. So ... I was thinking that now w
- /html/shop-talk/1998-04/msg00046.html (8,204 bytes)
- 48. Re: Shop Tools (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Fri, 17 Apr 1998 14:09:48 -0400
- Found Harbor Freight on the Internet and have just looked at an Enco catalog and I'm drooling all over the place ! I have a couple of questions for any of you who have these machines. Is there any su
- /html/shop-talk/1998-04/msg00049.html (8,899 bytes)
- 49. Fwd: Re: Shop Tools (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Fri, 17 Apr 1998 16:58:16 -0400
-
- /html/shop-talk/1998-04/msg00050.html (8,132 bytes)
- 50. Re: Brake Fluid (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Mon, 20 Apr 1998 16:29:17 -0400
- Also check by looking at the color (all DOT 3 fluid is relatively clear and Silicone fluid is usually a bright color like blue or yellow) Regards, Nils
- /html/shop-talk/1998-04/msg00095.html (7,283 bytes)
- 51. Re: Cheap workbench advice wanted. (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 21 Apr 1998 09:28:23 -0400
- What's wrong with pressure treated lumber ? Nils
- /html/shop-talk/1998-04/msg00105.html (8,408 bytes)
- 52. Re: Cheap workbench advice wanted. (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 21 Apr 1998 09:39:23 -0400
- I don't think you have to worry about the little bit of arsenic used in treated lumber. It's used extensively in all the decks and lawn furniture / children's play structures etc. where you come int
- /html/shop-talk/1998-04/msg00106.html (9,074 bytes)
- 53. Re: Cheap workbench advice wanted. (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 21 Apr 1998 13:08:47 -0400
- Personally, I can't think of a worse material for a workbench ! Presumably the bench is outside in an non air conditioned garage so the stuff will absorb moisture and swell during the summer (at leas
- /html/shop-talk/1998-04/msg00110.html (8,165 bytes)
- 54. Re: Shop Tools (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 21 Apr 1998 13:19:37 -0400
- I'm alarmed to hear these kind of things about a place I'm considering ordering from ! Is this from personal experience ? Do you have one of these low cost milling machines ? If so which one and what
- /html/shop-talk/1998-04/msg00111.html (8,208 bytes)
- 55. Re: Shop Tools (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 21 Apr 1998 15:20:05 -0400
- slightly higher, they tend to be more of a "in replacement type parts. Thanks for the suggestion ... someone else also suggested Grizzly and I am familiar with them as they offer a lot of woodworking
- /html/shop-talk/1998-04/msg00113.html (8,901 bytes)
- 56. RE: Arsenic (Was: Cheap workbench advice wanted.) (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Wed, 22 Apr 1998 16:10:26 -0400
- If you are a healthy normal adult I would not worry about it at all ! As far as I know the effects are not cumulative like that form lead or mercury. If you are affected in any minor way stop eating
- /html/shop-talk/1998-04/msg00123.html (7,629 bytes)
- 57. Re: Loc-Tite vs. Anti-Sieze (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Wed, 29 Apr 1998 14:31:32 -0400
- I would not use Loc-Tite on engine studs. The whole idea is that you don't want to go through the drilling bit again when a stud breaks and that is exactly what you will end up doing if you use the L
- /html/shop-talk/1998-04/msg00144.html (9,109 bytes)
- 58. Re: Loc-Tite vs. Anti-Sieze (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Thu, 30 Apr 1998 14:00:43 -0400
- I think you are missing the point here ! Studs used in engine blocks were not intended to be put in with Loc-Tite or similar products. There is no problem removing studs that are not broken (Everyon
- /html/shop-talk/1998-04/msg00149.html (8,478 bytes)
- 59. Re: Air Compressor (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Tue, 17 Mar 1998 17:13:24 -0500
- ALLRIGHT...... I'll bite what the hell is IMHO ?
- /html/shop-talk/1998-03/msg00027.html (7,856 bytes)
- 60. Re: Air Compressor (score: 1)
- Author: "Nils O. Ny" <n.ny@intest.com>
- Date: Wed, 18 Mar 1998 10:24:13 -0500
- Assuming that you have a motor that is about 90% efficient you would need a size 8 wire and a 40 amp breaker to get 5 HP
- /html/shop-talk/1998-03/msg00048.html (8,646 bytes)
This search system is powered by
Namazu