I was going to have my exhaust ran by a muffler shop, but it will be a lot cheaper for me to do it myself. Before I do it I want to know if you have any tips for me. I have a 50 3100 with a 350/350 c
I got a bracket kit for $60 dollars or so and it uses a mustang II master cylinder/power booster set up. These are some of the cheapest ms and pb you can get from a parts store. It probably wouldnt b
I have a Painless 18 circuit wiring harness and have had no problems with it except that it has not so good instructions for hooking up a fan relay and switch. I have a 350 in my truck and picked up
I have a painless wiring harness with an 86 firebird steering colum in my 50 3100. I am working on installing a classic gauges 5 inch electric speedo. The directions say to hook a wire from the spot
Hi everyone, I need to find a good place to get some gauges for my 50 3100. I would like to go with a speedo, tach, fuel, oil, water, and volt. I need it to have a programable speedo and would like t
im stuck. i have a th350 in my 50 3100 and the accumalater housing is leaking. i picked up the 'o' ring seal for it, but i cant figure out how to get the cover off to replace the seal. id appreciate
I have a 350/350 combo im going to install in my 50 3100 soon and i have a few questions about it: 1) Do i remove both of the original cross members and bolt in the new ones? Both are the tubular typ
What do you all recomend for a gas tank to mount under the bed of my 50 Chevy 3100? I can get about any gas tank through work at a good price. Thanks Rob oletrucks is devoted to Chevy and GM trucks b
i just picked up a 10 bolt posi rearend out of a 78 trans am that i am going to put in to my 50 3100. brother's sells an instalation kit for it that runs $140 or thereabouts. I was wondering if any o
Here's a question for all of you: would i be able to use a mid 80s colum and gearbox out of a chevy van for my powersteering swap? I know a late 70s colum works well and the kit from chevy duty says
On my 50 3100 Chevy I went with a front disc brake kit from Chevy Duty. Im very happy with it but what size wheels fit up there? Im worried with clearance and want to go with either 15 or 16 inch cus
They let out hydrogen gas, not bad or toxic, but i wouldnt be smoking around Rob oletrucks is devoted to Chevy and GM trucks built between 1941 and 1959
Its the hydrogen gas that it is emitted during charging (i believe another gas may be emitted also) that is what to watch out for. It won't harm you by itself but you definitly don't want to be smoki
Im putting a higher performance 350/350 combo (around 375hp and 400ft/lbs) in my 50 3100. I have the stock front axle with front disks brakes. The rotors have a mid 70s GM bolt pattern (like a chevel
I know that this is an off subject vehical but im sure there are some pretty damn good mechanics on the list that could help me out with this. I have a 1986 Ford Ranger that backfires throught the ta
No, its like a core charge. Hes looking for another one he can recrome and charging less if you give him an old one is giving you incentive to give him a core. Its just like getting charged an extra
How do you box a frame? Im putting a higher performance 350/350 combo in my 50 3100 and am wondering now how is this going to hurt the frame and how do i go about boxing it? Thanks Rob oletrucks is d
Just wanted to let you all know that when i was bored at work today i started looking through our exhaust catalog here at Oreilly Auto Parts and it looks like there isnt too much that you cant get fo
Ok, im a little, well........frustrated. I bought the front disc brake kit from chevy duty for my '50 3100. I heated the adapters that go on the spindles in my oven like one of the guys there told my