Mail Archive Search: <+subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Land\-speed\]\s+Cooling\s+an\s+8\-71\s*$/>

Results:

References: [ +subject:/^(?:^\s*(re|sv|fwd|fw)[\[\]\d]*[:>-]+\s*)*\[Land\-speed\]\s+Cooling\s+an\s+8\-71\s*$/: 7 ]

Total 7 documents matching your query.

1. [Land-speed] Cooling an 8-71 (score: 1): Author: "saltrat@pahrump.com" <saltrat@pahrump.com>; Date: Sat, 23 Jul 2011 14:10:31 -0700; I have been having trouble keeping the teflon seals in my 8-71. The teflon melts and chunks out of the rotors after about 3 runs at the salt at 18% overdrive on a 430 inch engine. The guys at the blo; /html/land-speed/2011-07/msg00060.html (7,285 bytes)
2. Re: [Land-speed] Cooling an 8-71 (score: 1): Author: "Dave Dahlgren" <dahlgren536@comcast.net>; Date: Sat, 23 Jul 2011 18:36:37 -0400; How much boost as that will decribe what the charge air temp is and how much fuel you need to get it cold enough to be ok. I was always under the impression the port nozzles were for triming cylinder; /html/land-speed/2011-07/msg00061.html (8,183 bytes)
3. Re: [Land-speed] Cooling an 8-71 (score: 1): Author: "John Burk" <joyseydevil@comcast.net>; Date: Sun, 24 Jul 2011 00:09:27 -0400; Have you asked about using nylatron strips instead of teflon . _______________________________________________ Land-speed@autox.team.net Donate: http://www.team.net/donate.html Archive: http://www.t; /html/land-speed/2011-07/msg00062.html (7,205 bytes)
4. Re: [Land-speed] Cooling an 8-71 (score: 1): Author: "Skip Higginbotham" <saltrat@pahrump.com>; Date: Sun, 24 Jul 2011 14:43:08 -0700; Thanks John, I think the strips on the center of the rotor lobe is Nylatron....Black.... The strips on the inside of the rotor are white....I assume Teflon. All of it seems to be melting. Skip ______; /html/land-speed/2011-07/msg00063.html (8,880 bytes)
5. [Land-speed] Cooling an 8-71 (score: 1): Author: "Kirkwood" <saltfever@comcast.net>; Date: Sun, 24 Jul 2011 22:28:08 -0700; Yeah Skip, it is a perilous problem. Right now you have a very lean mix up there. You know how lean AFR acts . . . lazy, slow-burn, and most likely not ignitable. As you increase the AFR inside the b; /html/land-speed/2011-07/msg00065.html (7,598 bytes)
6. Re: [Land-speed] Cooling an 8-71 (score: 1): Author: "Dave Dahlgren" <dahlgren536@comcast.net>; Date: Mon, 25 Jul 2011 15:55:01 -0400; If it backfires it is all going to go bang.. Does not matter top or bottom.. They will not give any tuneup info as they do not want any responsibility for whatever happens next.. Dave -- Original Mes; /html/land-speed/2011-07/msg00066.html (8,012 bytes)
7. [Land-speed] Cooling an 8-71 (score: 1): Author: "Kirkwood" <saltfever@comcast.net>; Date: Tue, 26 Jul 2011 00:11:05 -0700; Skip: I doubt your blower shop hasn't already optimized the seal material so this may only be interesting information without application. However, check out the table and compare Polyether ether ket; /html/land-speed/2011-07/msg00067.html (7,521 bytes)

Current List: 1 - 7
Page: [1]