Ayer, John K wrote:
>
> My bonnet mounts came slotted (as far as I know) from the factory.
> At least I always assumed that. Now that I think about it, they do look
>pretty home-built...
>
> So now I am certain Blackpool did it :)
>
Good logic which is likely to be correct. I will take pictures of
my rose joint solution when it is finished.
Regards,
JU
> Kimball Ayer
> '77 2500M
> #3723TM
>
> > ----------
> > From: Rolf Beuttenmuller[SMTP:rolf@bnl.gov]
> > Reply To: Rolf Beuttenmuller
> > Sent: Thursday, January 27, 2000 10:06 PM
> > To: Dr John Upham
> > Cc: tvr
> > Subject: Re: Bonnet hinging
> >
> > Hi John;
> >
> > I sloted the chassis mounting plates. I have had the same exact setup for
> > about 20 years.
> >
> > While I have your attention who is a good source for new headlight buckets.?
> >
> > Rolf 70 Vixen S2
> >
> > ----- Original Message -----
> > From: "Dr John Upham" <webmaster@ukmotorsport.com>
> > To: "Rolf Beuttenmuller" <rolf@bnl.gov>
> > Cc: "Matthew Towns" <mtowns@westsussex.gov.uk>; "Russell Towns"
> > <russell.towns@kvaerner.com>; "Russell Talbot"
> > <russell@hockerley.freeserve.co.uk>; "TVR US mailing list"
> > <tvr@autox.team.net>; "TVR Mailing List" <tvr@domino.com>; "Adrian Venn"
> > <adrian@exactly-tvr.demon.co.uk>
> > Sent: Tuesday, August 22, 2000 3:38 PM
> > Subject: TVR: Bonnet hinging
> >
> >
> > > I'm looking at better solution for hinging my new Vixen bonnet using
> > > spherical rod ends or rose joints. The thread in the DavidGerald
> > > fitted frame is 3/8 UNF and the std for rose joints is UNF as
> > > its an American aircraft spec. So two, 3/8 UNF male rose joints
> > > screw into the frame and then mount a 3/8 bit of rod on the brackets
> > > holding the water radiator. The question is: how to provide fore and
> > > aft adjustment?
> > >
> > > Ideas anyone?
> > >
> > > Regards,
> > >
> > > John
> > >
> > > --
> > > Dr John Upham, The UKMotorSport Index,
> > > http://www.ukmotorsport.com/, webmaster@ukmotorsport.com,
> > > Voice: +44 (0) 976 634 053 (W), Voice: +44 (0) 125 287 2551 (H),
> > > Voice: +44 (0) 976 634 053 (M)
> > > Registered address: Reid House, Mill Hall, Cuckfield, West Sussex RH17
> > > 5HX
> > > Registered number: 3445711
> >
> >
--
Dr John Upham, The UKMotorSport Index,
http://www.ukmotorsport.com/, webmaster@ukmotorsport.com,
Voice: +44 (0) 976 634 053 (W), Voice: +44 (0) 125 287 2551 (H),
Voice: +44 (0) 976 634 053 (M)
Registered address: Reid House, Mill Hall, Cuckfield, West Sussex RH17
5HX
Registered number: 3445711
|