triumphs
[Top] [All Lists]

Re: [TR] Triumphs Digest, Vol 14, Issue 63

To: triumphs@autox.team.net
Subject: Re: [TR] Triumphs Digest, Vol 14, Issue 63
From: "Gregmogdoc@surfnetusa.com" <Gregmogdoc@surfnetusa.com>
Date: Fri, 12 Mar 2021 09:37:33 -0800
Delivered-to: mharc@autox.team.net
Delivered-to: triumphs@autox.team.net
WE have reused TR-4 cylinder head stud over and over many times with no 
failures.  We inspect them for thread distortion and discard them if the 
threads are damaged. We will also discard studs that have excessive rust damage 
& pitting.  We torque the head nuts to 85 lbs. ft or torque using permatex 
"never sieze" on the threads and under the nut where it presses on the flat 
washer. we make sure to use good, hard, flat, & undamaged washers.  "MR. 
Gasket" 1/2 head washers work well a couple of times, thenm need to be 
replaced. They are inexpensive.  I believe that they are made to fit a Poniac 
v-8.  
    We torque the head cold, warm up the engine and then retorque the nuts 
again with the engine at full operating temp.  It is not necessary to torque 
the head to 105 lbs. ft!  We have used stock Payan gaskets, the genuine Payan 
steel shim gaskets, & other aftermarket gaskets and thay all work well with 
this proceedure.  We have not had success with solid copper sheet gaskets.  We 
like the liner projection to be around .005" with no more than .001" variation 
between adjacent cylinders.
                                                      Greg Solow



------- Original Message -------
>From    : 
>triumphs-request@autox.team.net[mailto:triumphs-request@autox.team.net]
Sent    : 3/10/2021 11:00:02 AM
To      : triumphs@autox.team.net
Cc      : 
Subject : RE: Triumphs Digest, Vol 14, Issue 63

 Send Triumphs mailing list submissions to
        triumphs@autox.team.net

To subscribe or unsubscribe via the World Wide Web, visit
         http://autox.team.net/mailman/listinfo/triumphs 
or, via email, send a message with subject or body 'help' to
        triumphs-request@autox.team.net

You can reach the person managing the list at
        triumphs-owner@autox.team.net

When replying, please edit your Subject line so it is more specific
than "Re: Contents of Triumphs digest..."


Today's Topics:

   1. would any of you re-use head studs? (Cliff Hansen)
   2. Re: would any of you re-use head studs? (Greg Lemon)
   3. Re: would any of you re-use head studs? (bill beecher)
   4. Re: would any of you re-use head studs? (Steve Kirby)
   5. Re: would any of you re-use head studs? (Frank Fisher)
   6. Re: would any of you re-use head studs? (Bob)


----------------------------------------------------------------------

Message: 1
Date: Tue, 9 Mar 2021 19:06:01 +0000


I respect your collective advice and experience. The 4A?s head is at the 
machinist for a cleanup (head gasket failure). Would any of you re-use the head 
studs, or would you replace them? They are likely original, and even if not, 
have been in place for at least 25 years. I have my thoughts on this, but am 
interested in yours.

Thanks,

Cliff


Sent from Mail< https://go.microsoft.com/fwlink/?LinkId=550986>  for Windows 10

-------------- next part --------------
An HTML attachment was scrubbed...
URL: < 
http://autox.team.net/pipermail/triumphs/attachments/20210309/452b82db/attachment-0001.htm>
 

------------------------------

Message: 2
Date: Tue, 9 Mar 2021 13:14:46 -0600


I know some people always replace them, I have never replaced them and
never had a problem with head gaskets or heads--the includes Sprite/Midget,
MGB, 4 and 6 cylinder TR, and big Healey.

Somebody, maybe Randall, said run a good nut up and down the thread, if
stretched it will bind.

Greg Lemon, TR250

On Tue, Mar 9, 2021, 1:06 PM Cliff Hansen <cliff_hansen@outlook.com> wrote:

> I respect your collective advice and experience. The 4A?s head is at the
> machinist for a cleanup (head gasket failure). Would any of you re-use the
> head studs, or would you replace them? They are likely original, and even
> if not, have been in place for at least 25 years. I have my thoughts on
> this, but am interested in yours.
>
>
>
> Thanks,
>
>
>
> Cliff
>
>
>
>
>
> Sent from Mail < https://go.microsoft.com/fwlink/?LinkId=550986>  for
> Windows 10
>
>
> ** triumphs@autox.team.net **
>
> Donate:  http://www.team.net/donate.html 
> Archive:  http://www.team.net/pipermail/triumphs 
>  http://www.team.net/archive 
>
> Unsubscribe/Manage:
>  http://autox.team.net/mailman/options/triumphs/grglmn@gmail.com 
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: < 
http://autox.team.net/pipermail/triumphs/attachments/20210309/ed3a5734/attachment-0001.htm>
 

------------------------------

Message: 3
Date: Tue, 9 Mar 2021 13:17:35 -0600


I have re-used TR3 head studs. One failure that shot the stud into the bonnet 
with enough force to create a 1/2? dimple.  
Bill

#dontkillgrandma

On Mar 9, 2021, at 1:06 PM, Cliff Hansen <cliff_hansen@outlook.com> wrote:

?
I respect your collective advice and experience. The 4A?s head is at the 
machinist for a cleanup (head gasket failure). Would any of you re-use the head 
studs, or would you replace them? They are likely original, and even if not, 
have been in place for at least 25 years. I have my thoughts on this, but am 
interested in yours.
 
Thanks,
 
Cliff
 
 
Sent from Mail for Windows 10
 
** triumphs@autox.team.net **

Archive:  http://www.team.net/pipermail/triumphs    http://www.team.net/archive 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: < 
http://autox.team.net/pipermail/triumphs/attachments/20210309/6f670920/attachment-0001.htm>
 

------------------------------

Message: 4
Date: Tue, 9 Mar 2021 19:25:23 +0000


Modern engines use a ?stretch to clamp? type of head stud which maintains the 
torque.  These are a ?one and done? part and cannot be reused, which has given 
rise to the myth that head studs should always be replaced.  Our old cars were 
not that technically sophisticated.  As long as the old studs show no signs of 
corrosion or other physical damage, there is no reason not to reuse them.  I 
would chase the threads on both the studs and nuts to be sure there is no 
binding which would give you a false torque reading.  I use the blue thread 
locker on the end that goes into the block and anti-seize on the nut end 
(though that is a subject of some debate).

Steve Kirby
President
China Auto Group
22831 Avenida Empresa
Rancho Santa Margarita, CA 92688 USA
Direct:  (949) 261-8208
Fax:  (949) 767-5949
Cell:  (949) 903-0957
Skype: steve.kirby29
www.chinaautogroup.com



I know some people always replace them, I have never replaced them and never 
had a problem with head gaskets or heads--the includes Sprite/Midget, MGB, 4 
and 6 cylinder TR, and big Healey.

Somebody, maybe Randall, said run a good nut up and down the thread, if 
stretched it will bind.

Greg Lemon, TR250

On Tue, Mar 9, 2021, 1:06 PM Cliff Hansen <cliff_hansen@outlook.com< 
mailto:cliff_hansen@outlook.com>>  wrote:
I respect your collective advice and experience. The 4A?s head is at the 
machinist for a cleanup (head gasket failure). Would any of you re-use the head 
studs, or would you replace them? They are likely original, and even if not, 
have been in place for at least 25 years. I have my thoughts on this, but am 
interested in yours.

Thanks,

Cliff


Sent from Mail< https://go.microsoft.com/fwlink/?LinkId=550986>  for Windows 10

** triumphs@autox.team.net< mailto:triumphs@autox.team.net>  **

Archive:  http://www.team.net/pipermail/triumphs    http://www.team.net/archive 







-------------- next part --------------
An HTML attachment was scrubbed...
URL: < 
http://autox.team.net/pipermail/triumphs/attachments/20210309/c67ba449/attachment-0001.htm>
 

------------------------------

Message: 5
Date: Tue, 9 Mar 2021 19:59:59 +0000 (UTC)


 i have never replaced head studs.they have considerable redundancy in their 
design i cant imagine them ever giving way.some people differ.
Frank



    On Tuesday, March 9, 2021, 11:06:40 AM PST, Cliff Hansen 
<cliff_hansen@outlook.com> wrote:  
 
  
I respect your collective advice and experience. The 4A?s head is at the 
machinist for a cleanup (head gasket failure). Would any of you re-use the head 
studs, or would you replace them? They are likely original, and even if not, 
have been in place for at least 25 years. I have my thoughts on this, but am 
interested in yours.

 ?
 
Thanks,

 ?
 
Cliff

 ?
 
 ?
 
Sent from Mail for Windows 10

 ?
 ** triumphs@autox.team.net **

Archive:  http://www.team.net/pipermail/triumphs    http://www.team.net/archive 

  
-------------- next part --------------
An HTML attachment was scrubbed...
URL: < 
http://autox.team.net/pipermail/triumphs/attachments/20210309/a6de80a5/attachment-0001.htm>
 

------------------------------

Message: 6
Date: Tue, 9 Mar 2021 15:50:32 -0500


Same here. I have never experienced a failure. I did strip a nut years 
back but I am guessing it was my fault.

Bob

On 3/9/21 2:59 PM, Frank Fisher wrote:
> i have never replaced head studs.
> they have considerable redundancy in their design i cant imagine them 
> ever giving way.
> some people differ.
>
> Frank
>
>
>
>
> On Tuesday, March 9, 2021, 11:06:40 AM PST, Cliff Hansen 
> <cliff_hansen@outlook.com> wrote:
>
>
> I respect your collective advice and experience. The 4A?s head is at 
> the machinist for a cleanup (head gasket failure). Would any of you 
> re-use the head studs, or would you replace them? They are likely 
> original, and even if not, have been in place for at least 25 years. I 
> have my thoughts on this, but am interested in yours.
>
> Thanks,
>
> Cliff
>
> Sent from Mail < https://go.microsoft.com/fwlink/?LinkId=550986>  for 
> Windows 10
>
> ** triumphs@autox.team.net < mailto:triumphs@autox.team.net>  **
>
> Donate:  http://www.team.net/donate.html 
> Archive:  http://www.team.net/pipermail/triumphs  
> < http://www.team.net/pipermail/triumphs  >  http://www.team.net/archive 
>
> Unsubscribe/Manage: 
>  http://autox.team.net/mailman/options/triumphs/yellowtr3@yahoo.com 
>
> ** triumphs@autox.team.net **
>
> Donate:  http://www.team.net/donate.html 
> Archive:  http://www.team.net/pipermail/triumphs    
> http://www.team.net/archive 
>
> Unsubscribe/Manage:  
> http://autox.team.net/mailman/options/triumphs/yellowtr@adelphia.net 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: < 
http://autox.team.net/pipermail/triumphs/attachments/20210309/6e214ae3/attachment-0001.htm>
 

------------------------------



_______________________________________________

Triumphs mailing list
Triumphs@autox.team.net
 http://autox.team.net/mailman/listinfo/triumphs 


------------------------------

End of Triumphs Digest, Vol 14, Issue 63
****************************************


** triumphs@autox.team.net **

Archive: http://www.team.net/pipermail/triumphs  http://www.team.net/archive


<Prev in Thread] Current Thread [Next in Thread>