--===============2377395318258720364==
--089e0149bd3eccdd0e0526e2dbc3
Content-Transfer-Encoding: quoted-printable
I=E2=80=99ve been fortunate enough to source myself a pair of half shafts f=
rom a
Triumph 2000. These apparently fit a Triumph Stag which I have. The shafts
come with replicable universal joints, unlike the staked type currently on
my Stag.
I can get two types of joint GUJ102 without zirk / grease nipple or GUJ107
with zirk / grease nipple. 2 are required per side. The problem with
GUJ107 is once fitted to the car there is no way to get to the zirk closet
to the hub as it is enclosed by the radius arm. I=E2=80=99m aware TR6s hav=
e a
similar setup.
So should I get 4 no-zirked type and fit once and forget, or buy the zirked
type and periodically, which means never in my case, re- grease by removing
the shaft?
Do the zirked type really need pumping with grease once in a while?
Also, doing a cross reference to other part numbers of the zirked type ,
prices vary from $11 to $25 Any recommendations on brand I found the ones
below.
I also found a cross reference to GMB
GUJ107 cross references these following parts
Factory Number
ACDelco 45U0168
BECK/ARNLEY 102-0031
BECK/ARNLEY 102-0106
REO 55P1
CARRARO 107625
JENSEN 94425
Regards, Sujit
--089e0149bd3eccdd0e0526e2dbc3
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr"><div class=3D"gmail_signature"><p class=3D"MsoNormal">I=E2=
=80=99ve been fortunate enough to source myself a pair of half
shafts from a Triumph 2000. These apparently fit a Triumph Stag which I hav=
e.
The shafts come with replicable universal joints, unlike the staked type
currently on my Stag.=C2=A0 </p>
<p class=3D"MsoNormal">I can get two types of joint GUJ102 without zirk / g=
rease nipple
or GUJ107 with zirk / grease nipple. 2 are required per side.=C2=A0 The pro=
blem with GUJ107 is once fitted to the
car there is no way to get to the zirk closet to the hub as it is enclosed =
by the
radius arm.=C2=A0 I=E2=80=99m aware TR6s have a
similar setup.</p>
<p class=3D"MsoNormal">So should I get 4 no-zirked type and fit once and fo=
rget, or
buy the zirked type and periodically, which means never in my case, re- gre=
ase
by removing the shaft?</p>
<p class=3D"MsoNormal">Do the zirked type really need pumping with grease o=
nce in a
while?</p>
<p class=3D"MsoNormal">Also, doing a cross reference to other part numbers =
of the
zirked type , prices vary from $11 to $25 Any recommendations on brand I fo=
und the
ones below. </p>
<p class=3D"MsoNormal">I also found a cross reference to GMB</p>
<p class=3D"MsoNormal"><br>
<br>
</p>
<p class=3D"MsoNormal">GUJ107 cross references these following parts</p>
<p class=3D"MsoNormal">Factory Number</p>
<p class=3D"MsoNormal">ACDelco=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=
=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0 45U0168</p>
<p class=3D"MsoNormal">BECK/ARNLEY=C2=A0=C2=A0=C2=A0 102-0031</p>
<p class=3D"MsoNormal">BECK/ARNLEY=C2=A0=C2=A0=C2=A0 102-0106</p>
<p class=3D"MsoNormal">REO=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0 55P1</=
p>
<p class=3D"MsoNormal">=C2=A0</p>
<p class=3D"MsoNormal">CARRARO=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=A0=C2=
=A0=C2=A0=C2=A0=C2=A0 107625</p>
<p class=3D"MsoNormal">JENSEN 94425</p>
<p class=3D"MsoNormal">=C2=A0</p>
<p class=3D"MsoNormal">Regards, Sujit</p></div>
</div>
--089e0149bd3eccdd0e0526e2dbc3--
--===============2377395318258720364==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
** triumphs@autox.team.net **
Archive: http://www.team.net/archive
--===============2377395318258720364==--
|