List:
And I understand that the first motion shaft from the GT6 MKIII will not
mesh with the Laygear (fourth gear position) Spitfire single or three rail
gearbox ?
-----Original Message-----
From: Ted Schumacher [mailto:tedtsimx@q1.net]
Sent: Monday, October 28, 2002 9:02 AM
To: SPIT6CGT6@yahoogroups.com
Cc: triumphs@autox.team.net; nass@yahoogroups.com
Subject: Re: [SPIT6CGT6] GT6 tranny ideas
brooks, the gt6 bellhousing is longer than the spit. if you set both
bellhousings face down on a bench and measure the height, the gt6 is about
3/4"
taller. therefore, the spit input shaft is "short" by 3/4" when attaching a
spit gerabox to a gt6 bellhousing. this leads to some serious issues with
the
spline engagement and also the pilot bushing. ted
Brooks Bullock wrote:
> Paul:
>
> I just asked Ted Shumacher that very same question and he was pretty quick
> to tell me that the bell housing made a different length for the
penetration
> of the first motion shaft in the pilot bush and wouldn't work. can't
> remember if it was too short or too long,hopefully Ted you are watching
this
> list, and could correct or add more to this.
>
> TIA
> Brooks
>
> -----Original Message-----
> From: ptegler@cablespeed [mailto:ptegler@cablespeed.com]
> Sent: Sunday, October 27, 2002 9:44 PM
> To: triumphs@autox.team.net; SPIT6CGT6@yahoogroups.com;
> nass@yahoogroups.com
> Subject: [SPIT6CGT6] GT6 tranny ideas
>
> OK... here goes... Am I off my rocker? is it worth it?
>
> For my new GT6 MKIII I'd prefer to have a J type rather than
> the D type O/D. so....
> Since I have a spare a 3 rail 4 speed GT6 tranny with
> aluminum bell housing, and a complete single rail Spit
> tranny, I'm considering the following ...
>
> Modify the GT6 input shaft (bore it out) to accept the
> larger tip and bearing of the single rail mainshaft and add
> the J type O/D. to the single rail case, using the GT6 gear
> set (laygear and shaft etc) and use the aluminum GT6
> bell housing on the single rail case
>
> Sound right? Feasible?
>
> Now... anybody have a clue what length driveshaft I'd need?
>
> Anybody have a 3.89 diff for a Spit/ GT6 they'd care to swap for a
> good 3.27 (plus spares if needed)??
>
> Paul Tegler
> ptegler@cablespeed.com
> www.teglerizer.com
>
> To unsubscribe from this group, send an email to:
> SPIT6CGT6-unsubscribe@egroups.com
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
>
>
> To unsubscribe from this group, send an email to:
> SPIT6CGT6-unsubscribe@egroups.com
>
>
>
> Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
--
Ted Schumacher
tedtsimx@q1.net
http://www.tsimportedautomotive.com
Pandora, Ohio, USA
Fax: 419/ 384-3272 (24 hrs.)
Phone: 800/ 543-6648 (US & Canada)
Tech/Gen Info/Worldwide: 419/ 384-3022
******************************************************
New - used - rebuilt - performance British car parts.
------------------------ Yahoo! Groups Sponsor ---------------------~-->
Sell a Home with Ease!
http://us.click.yahoo.com/SrPZMC/kTmEAA/jd3IAA/dJUxlB/TM
---------------------------------------------------------------------~->
To unsubscribe from this group, send an email to:
SPIT6CGT6-unsubscribe@egroups.com
Your use of Yahoo! Groups is subject to http://docs.yahoo.com/info/terms/
/// triumphs@autox.team.net mailing list
/// or try http://www.team.net/cgi-bin/majorcool
/// Archives at http://www.team.net/archive
|