This is a multipart message in MIME format.
--===============5124765181572158692==
boundary="----=_NextPart_000_0008_01D69BD5.6390ED70"
Content-Language: en-us
This is a multipart message in MIME format.
------=_NextPart_000_0008_01D69BD5.6390ED70
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
Rick
1 =E2=80=93 =C2=BD=E2=80=9D heater hose from heater core to heater valve =
or =E2=80=9CT=E2=80=9D piece and from valve to temp sender block
All other hoses are 5/8=E2=80=9D heater hose
I put a hose interchange list on TEAE web site that can help you=20
Sunbeam Specialties carries hoses
=20
=20
2 =E2=80=93 vacuum hard line is 3/16=E2=80=9D with double compression =
fittings on the original stock line
If you buy a formed vacuum line from one of the Mustang catalogs =
=E2=80=93 the line is too long and needs to be shortened at each end =
=E2=80=93 Tiger length is about 25=E2=80=9D=20
=20
3 =E2=80=93 5/16=E2=80=9D fuel line hose =E2=80=93 4=E2=80=9D long =
=E2=80=93 original hose has a very rough outside texture
=20
4 =E2=80=93 the original Ford ignition wires used both 90 and straight
Original style wire sets available in Mustang catalogs like National =
Parts Depot
If you have headers you may need something better for the heat
=20
Ron Fraser
=20
From: Tigers <tigers-bounces@autox.team.net> On Behalf Of R Flynn via =
Tigers
Sent: Monday, October 05, 2020 6:00 PM
To: <tigers@Autox.Team.Net> <tigers@autox.team.net>
Cc: R Flynn <flynnr2@gmail.com>
Subject: [Tigers] ? questions
=20
Looking for some information / advice (now that it is running again, =
looking to tidy up a few bits, etc.) which I hope someone can help me =
with.
=20
1) What size are the hoses which runs to & from the MKI (so S1-SIV =
Alpines too I think) heater valve (manifold -> valve -> heater core)?
My heater valve is leaking like a sieve and replacements appear to be =
scarce at the moment, so looking to bypass it until it can be rectified.
=20
2) I assume the distributor vacuum line is the standard 3/16"?
Mine is a bit short / tight, does not inspire confidence.
=20
3) What sort of hose is used in the fuel line around the transmission / =
engine area?
Mine is a bit mishappen, again does not inspire confidence.
=20
4) Any opinion on spark wire boots - 90 vs 135 degrees?
Looking at ordering a kit to make some up, need to make an all in =
choice.
=20
Cheers in advance,
=20
--=20
rick
B9471206: http://www.tigersunited.com/car_show/flynn_r/default.asp
------=_NextPart_000_0008_01D69BD5.6390ED70
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" =
xmlns:o=3D"urn:schemas-microsoft-com:office:office" =
xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml"; =
xmlns=3D"http://www.w3.org/TR/REC-html40";><head><meta =
http-equiv=3DContent-Type content=3D"text/html; charset=3Dutf-8"><meta =
name=3DGenerator content=3D"Microsoft Word 15 (filtered =
medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
span.EmailStyle18
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-size:10.0pt;
font-family:"Calibri",sans-serif;}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DEN-US link=3Dblue =
vlink=3Dpurple><div class=3DWordSection1><p =
class=3DMsoNormal>Rick<o:p></o:p></p><p class=3DMsoNormal>1 =E2=80=93 =
=C2=BD=E2=80=9D heater hose from heater core to heater valve or =
=E2=80=9CT=E2=80=9D piece and from valve to temp sender =
block<o:p></o:p></p><p class=3DMsoNormal>All other hoses are =
5/8=E2=80=9D heater hose<o:p></o:p></p><p class=3DMsoNormal>I put a hose =
interchange list on TEAE web site that can help you <o:p></o:p></p><p =
class=3DMsoNormal>Sunbeam Specialties carries hoses<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>2 =E2=80=93 =
vacuum hard line is 3/16=E2=80=9D with double compression fittings on =
the original stock line<o:p></o:p></p><p class=3DMsoNormal>If you buy a =
formed vacuum line from one of the Mustang catalogs =E2=80=93 the line =
is too long and needs to be shortened at each end =E2=80=93 Tiger length =
is about 25=E2=80=9D <o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>3 =E2=80=93 =
5/16=E2=80=9D fuel line hose =E2=80=93 4=E2=80=9D long =E2=80=93 =
original hose has a very rough outside texture<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal>4 =E2=80=93 =
the original Ford ignition wires used both 90 and =
straight<o:p></o:p></p><p class=3DMsoNormal>Original style wire sets =
available in Mustang catalogs like National Parts Depot<o:p></o:p></p><p =
class=3DMsoNormal>If you have headers you may need something better for =
the heat<o:p></o:p></p><p class=3DMsoNormal><o:p> </o:p></p><p =
class=3DMsoNormal>Ron Fraser<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><p class=3DMsoNormal><b>From:</b> =
Tigers <tigers-bounces@autox.team.net> <b>On Behalf Of </b>R Flynn =
via Tigers<br><b>Sent:</b> Monday, October 05, 2020 6:00 =
PM<br><b>To:</b> <tigers@Autox.Team.Net> =
<tigers@autox.team.net><br><b>Cc:</b> R Flynn =
<flynnr2@gmail.com><br><b>Subject:</b> [Tigers] ? =
questions<o:p></o:p></p><p =
class=3DMsoNormal><o:p> </o:p></p><div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>Looking for some =
information / advice (now that it is running again, looking to tidy up a =
few bits, etc.) which I hope someone can help me =
with.<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-size:12.0pt'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>1) What size are the =
hoses which runs to & from the MKI (so S1-SIV Alpines too I think) =
heater valve (manifold -> valve -> heater =
core)?<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-size:12.0pt'>My heater valve is leaking like a sieve and =
replacements appear to be scarce at the moment, so looking to bypass it =
until it can be rectified.<o:p></o:p></span></p></div><div><p =
class=3DMsoNormal><span =
style=3D'font-size:12.0pt'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>2) I assume the =
distributor vacuum line is the standard 3/16"?<br>Mine is a bit =
short / tight, does not inspire =
confidence.<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-size:12.0pt'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>3) What sort of hose =
is used in the fuel line around the transmission / engine =
area?<br>Mine is a bit mishappen, again does not inspire =
confidence.<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-size:12.0pt'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>4) Any opinion on =
spark wire boots - 90 vs 135 degrees?<o:p></o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>Looking at ordering a =
kit to make some up, need to make an all in =
choice.<o:p></o:p></span></p></div><div><p class=3DMsoNormal><span =
style=3D'font-size:12.0pt'><o:p> </o:p></span></p></div><div><p =
class=3DMsoNormal><span style=3D'font-size:12.0pt'>Cheers in =
advance,<o:p></o:p></span></p></div><div><p =
class=3DMsoNormal><o:p> </o:p></p></div><p class=3DMsoNormal>-- =
<o:p></o:p></p><div><p class=3DMsoNormal>rick<br>B9471206: <a =
href=3D"http://www.tigersunited.com/car_show/flynn_r/default.asp"; =
target=3D"_blank">http://www.tigersunited.com/car_show/flynn_r/default.as=
p</a><o:p></o:p></p></div></div></div></body></html>
------=_NextPart_000_0008_01D69BD5.6390ED70--
--===============5124765181572158692==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/pipermail/tigers http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
--===============5124765181572158692==--
|