This is a multi-part message in MIME format.
--===============5577270716612199954==
boundary="----=_NextPart_000_0004_01D10B4E.12DB6DA0"
This is a multi-part message in MIME format.
------=_NextPart_000_0004_01D10B4E.12DB6DA0
charset="us-ascii"
Content-Transfer-Encoding: quoted-printable
I set up a fixture - 289 oil pan, timing cover and oil pump with pick up
=20
I used my 260 Tiger dipstick and tube. The end of this dipstick is =
about
1/2" off the bottom of the oil pan.
=20
Leveled fixture front to back, side to side
=20
2qt - level is at ADD line
3qt - level is 1/4" below FULL line
4qt - level is at the top L of FULL
=20
Tiger oil lines hold about 4 oz
=20
I calculated the volume for oil filters - actual fluid measurements =
probably
vary
Fram PH8A =3D 49.214 cu in =3D 27.27 oz =3D 1.7 pt ( 1.7 + .25 =3D =
1.95 pt)
almost 1qt
Fram PH3600 =3D 34.289 cu in =3D 18.99 oz =3D 1.18 pt
=20
I measured the angle of my Tiger engine at 2 degrees tilted down at =
front
I measured the angle of my 1988 Mustang engine at 4 degrees tilted down =
at
back
=20
Tilt test
2 degree front 3qt - level is at FULL line
4qt - level is 1/16" below Ford logo oval
=20
5 degree back 3qt - level is 1/4" above ADD line or just below mid =
line
4qt - level is 1/8" below FULL line
=20
I never think the tilt of the engine would mean so much but there you =
have
it - Tilt means everything with respect to the dipstick.
=20
Ron Fraser
=20
------=_NextPart_000_0004_01D10B4E.12DB6DA0
charset="us-ascii"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META HTTP-EQUIV=3D"Content-Type" CONTENT=3D"text/html; =
charset=3Dus-ascii">
<TITLE>Message</TITLE>
<META name=3DGENERATOR content=3D"MSHTML 8.00.6001.23588"></HEAD>
<BODY>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>I set =
up a fixture -=20
289 oil pan, timing cover and oil pump with pick up</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>I used =
my=20
260 Tiger dipstick and tube. The end of=20
this dipstick is about 1/2" off the bottom of the oil=20
pan.</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN =
class=3D312031019-20102015>Leveled fixture=20
front to back, side to side</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>2qt - =
level is at=20
ADD line</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>3qt - =
level=20
is 1/4" below FULL line</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>4qt - =
level is at=20
the top L of FULL</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>Tiger =
oil lines hold=20
about 4 oz</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>I =
calculated the=20
volume for oil filters - actual fluid measurements probably=20
vary</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>Fram =
PH8A =3D 49.214=20
cu in =3D 27.27 oz =3D 1.7 pt ( 1.7 + .25 =3D 1.95 pt) =
almost=20
1qt</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>Fram =
PH3600 =3D 34.289=20
cu in =3D 18.99 oz =3D 1.18 pt</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>I =
measured the angle=20
of my Tiger engine at 2 degrees tilted down at front</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>I =
measured the angle=20
of my 1988 Mustang engine at 4 degrees tilted down=20
at back</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>Tilt=20
test</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>2 =
degree=20
front 3qt - level is at FULL=20
line</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015> &nbs=
p;  =
; =20
4qt - level is 1/16" below Ford logo oval</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>5 =
degree=20
back 3qt - level is 1/4" above ADD line or just below =
mid=20
line</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015> &nbs=
p;  =
; =20
4qt - level is 1/8" below FULL line</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN =
class=3D312031019-20102015>I never think=20
the tilt of the engine would mean so much but there you have it - =
Tilt=20
means everything with respect to the dipstick.</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN class=3D312031019-20102015>Ron=20
Fraser</SPAN></FONT></DIV>
<DIV><FONT size=3D2 face=3DArial><SPAN=20
class=3D312031019-20102015></SPAN></FONT> </DIV></BODY></HTML>
------=_NextPart_000_0004_01D10B4E.12DB6DA0--
--===============5577270716612199954==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
tigers@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/tigers/mharc@autox.team.net
--===============5577270716612199954==--
|