tigers
[Top] [All Lists]

Re: [Tigers] MK II wiring help

To: tigers@autox.team.net, " Ron Fraser" <rfraser@bluefrog.com>
Subject: Re: [Tigers] MK II wiring help
From: Tod Brown <todbrown@roadrunner.com>
Date: Fri, 27 Apr 2012 15:37:55 -0400
Delivered-to: tigers-archive@autox.team.net
Delivered-to: tigers@autox.team.net
List-archive: <http://autox.team.net/pipermail/tigers>
List-help: <mailto:tigers-request@autox.team.net?subject=help>
List-id: Sunbeam Tigers <tigers.autox.team.net>
List-post: <mailto:tigers@autox.team.net>
List-subscribe: <http://autox.team.net/mailman/listinfo/tigers>, <mailto:tigers-request@autox.team.net?subject=subscribe>
List-unsubscribe: <http://autox.team.net/mailman/options/tigers>, <mailto:tigers-request@autox.team.net?subject=unsubscribe>
User-agent: Mozilla/5.0 (Windows NT 6.0; rv:11.0) Gecko/20120327 Thunderbird/11.0.1
Ron:

I don't know if this will help but the Shop Manual shows the wiring for 
an ammeter for a MkIA but not for the MkII.  I know the ammeter was 
optional on the MkIA and the wiring diagram shows the ammeter with 
dashed lines replacing the wire that runs from the "B" (Battery) 
terminal on the voltage regulator to the terminal on the solenoid that 
is connected to the positive battery terminal.  I conclude from this and 
seem to remember that, on my MkIA, the large brown wire going to the 
voltage regulator comes from the solenoid rather than directly from the 
alternator/generator.

At least some of the MkII's had ammeters that matched the other 
instrumentation but it does not look like they were delivered from the 
factory that way which is probably why it is not shown on the wiring 
diagram.  Since the MkII's used alternators, I recollect that the 
ammeter range was higher,  + or - 50 amps, while the MkIA's were + or - 
30 amps.

In the CAT Notes there is an entry entitled, "Ammeter Installation" from 
Greg Tuttle added in the Mid-70s, it says.  To quote,

"... Before doing anything, disconnect the battery. ...

Next, remove the large brown wire from the top pole of the voltage 
regulator.  Remove connector and solder splice another piece of 10 ga 
wire and run back through the firewall to the + (plus) side of the 
meter.  Run another piece of 10 ga wire from the - (negative) side back 
to the regulator and attach to top pole.  Use suitable connectors at all 
four points, as a lot of current passes through them.  Tape splice as 
necessary.

Wire lamp by inserting plug on red wire into connector in harness under 
dash; ground black wire to tach mounting post.

Check that connections are tight and well insulated and reconnect 
battery.  Turn lights on and verify needle moves to - or discharge side 
of meter.  If needle shows + or charge with lights on, reverse the two 
wires on the back of the meter."

Although the instructions may have been written for the MkIA, they 
should also work for the MkII because the large brown wire, in both 
cases, carries the current to and from the positive terminal of the 
battery, and that is, of course, what you want the ammeter to read.

Good luck,

Tod
B382002384LRXFE
_______________________________________________

tigers@autox.team.net

Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: 
http://autox.team.net/mailman/options/tigers/tigers-archive@autox.team.net



<Prev in Thread] Current Thread [Next in Thread>