I have a spare generator bracket so I took a look at it. On the back side is
molded an underscored delta (triangle) followed by a "2". Below that is
"10039-B".The tapped hole on the top of the bracket is where the clamp for the
heater hose (coming out of the water pump) attaches.
Will Seay - 382001570
wseay@embarqmail.com
-----Original Message-----
From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net] On
Behalf Of Thomas Witt
Sent: Saturday, September 10, 2011 4:54 PM
To: tigers@autox.team.net
Subject: Re: [Tigers] Generator bracket
I looked at my generator bracket and as stated there was no number. There
was a slightly raise oval area that looked like it might have been the place
to put it... but, no. Also, there was a tapped in pin on my bracket to hold
"something" - just curious.
Tom
>I might be stating the obvious, but the standard Ford generator bracket has
> a rectangle or square (depending on year) opening cut in it to facilitate
> the dipstick. The Tiger generator bracket has no such hole, with the
> dipstick attached to the front of the Tiger generator bracket.
>
> Kirk
>
> -----Original Message-----
> From: tigers-bounces@autox.team.net [mailto:tigers-bounces@autox.team.net]
> On Behalf Of Ron Fraser
> Sent: Saturday, September 10, 2011 5:11 AM
> To: 'RObin Young'; genepadgett@comcast.net
> Cc: harryb@elams.org; tigers@autox.team.net
> Subject: Re: [Tigers] Generator bracket
>
> Robin
> I don't think there is any confusion; we are just seeking
> information about this part.
>
> I have stated the Tiger generator bracket was ordered by the Ford
> Industrial Division and carries a C4JZ part number in the Parts List. It
> is a Tiger specific part with no casting number. The offset is different
> from the stock Ford part to line up the fan belt on the Tiger 260 engine.
> The pulleys on the Tiger 260 engine also carry a C4JZ part number which
> makes them Tiger specific too.
>
> This does not mean that a stock Ford Generator bracket could not
> work but you would need to space the generator to the rear around 3/4" to
> line up the fan belt. You would also need to look for any hood clearance
> issues with the stock Ford bracket.
>
> The casting number for the stock Ford generator bracket is C2OE-10039-H.
> If
> anyone has a casting number on their Tiger generator bracket; I just ask
> that you report the full number and I will investigate that number as best
> I'm able.
>
> Ron Fraser
>
> -----Original Message-----
> From: RObin Young [mailto:robin02@mindspring.com]
> Sent: Friday, September 09, 2011 8:23 PM
> To: genepadgett@comcast.net; rfraser@bluefrog.com
> Cc: harryb@elams.org; tigers@autox.team.net
> Subject: RE: [Tigers] Generator bracket
>
>
> Ron, to further add to the confusion.....the bracket off B9471769 has
> only
> a triangle and a 2 stamped on it. Over the last couple of days, I dipped
> it
> and cleaned many coats of black paint off to find what appears to be a
> sand
> cast texture with no other marks. Robin Young
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/twotigers@verizon.net
> _______________________________________________
>
> tigers@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/tigers/atwittsend@verizon.net
_______________________________________________
tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Unsubscribe: http://autox.team.net/mailman/options/tigers/wseay@embarqmail.com
_______________________________________________
tigers@autox.team.net
Donate: http://www.team.net/donate.html
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
|