Mallary Unilite, with a 20k coil.
Regards-Chris in Trinidad
James Barrett wrote:
> Folks,
> Friday morning I headed for work and decided to
> see if I still had a slight backfire on acceleration. Well,
> I should not have done that. KABAMMMM !! The motor died
> and would not restart in neutral. I rolled into a DOALL
> parking lot and stopped. Tried to start it again and the
> loudest explosion I have ever heard came out of one tail pipe.
> I figured that I had an Ignition problem as I just receintly
> installed a MSD 6AL on the Tiger. I have a stock magnetic
> pickup Ford distributor.
> Pulled the distributor cap and noticed that the rotor
> was loose and rotated several degrees from normal. Checked the
> inside of the rotor and found that the plastic locator had
> mostly sheared off. No sign of contact with the distributor
> cap. Was able to get the rotor back in the slot of the
> distributor shaft and it appeared that it might hold until
> I could get home and replace it.
> About that time some guy drove up wanting to look
> at the Tiger. That took a while.
> Replaced the distributor cap and cranked it.
> No joy. Pulled the cap and using a screw driver near the
> magnetic pickup I determined that the MSD and the pickup
> were working. Got nice fat spark off of the coil wire.
> Cranked a bit more with the cap off and noticed the
> distributor/rotor was NOT turning. @#$!^%$#@!
> About that time DOALL opened and I was allowed to use
> their phone to call a wrecker. DOALL is an industrial
> supply house for bandsaws ( up to 2 1/2" bands), all kinds of
> machining tools and accessories, taps, dies, drill bits,
> chemical, etc. and flaring tools. I promply ordered a RIDGID
> flaring tool for about $45. Will let you know how that turns
> out.
> Short tow home and a call to work that I wouldn't be
> in. A gallon of oil dry added to the drive way where the wrecker
> dumped a couple of quarts of oil. At least it was clean oil.
> They have one very bad leak. I assume that they add a few quarts
> of oil before every towing job. By the way this was the very
> first time my Tiger has ever been towed.
>
> Pulled the distributor and 3 teeth were off of the
> distributor gear. Checked the cam gear and it appeared to be ok.
>
> Pulled the oil pan and found two teeth. Pulled the
> oil pump so I could remove the windage tray. Found the third tooth.
> Also noticed a full 1/2 spirial twist to the oil pump drive shaft.
> The oil pump was locked solid as well. Got the rotors out of the
> pump and the two parts are stuck together. There was no crud
> that locked up the pump. It is as if the internal rotor had moved
> slightly to one side and jammed its self into the outer rotor.
> There appears to be a tiny flat at the peak of the inner rotor
> where it is stuck to the outer rotor. Plan to use the rotors
> and drive shaft as a paper weight in my office. There was no sign
> of any scratches on the parts and the oil, all 14 quarts was
> clean.
> Had a good distributor gear from the older point type
> distributor. The broken gear had also sheared the roll pin
> so I had to use a cut off wheel to remove the broken gear.
> Found some gauling on the distributor shaft under the gear.
> By spinning the shaft with my electric drill I was abke to
> smooth the shaft. Forgot that the roll pin hole is off set
> on a Ford so I of course pressed the replacement gear on wrong.
> Was able to rotate 180 and put the roll pin in. Distributor
> now fixed.
> New high volumne oil pump, pickup tube, drive shaft,
> pan gasket, RTV, 24 quarts of 20-50 oil and a rotor went
> for $120. Called in the order and was able to get the parts
> Friday night just before they closed. Checked the pump,
> drive shaft, pickup tube and gaskets to be sure they were
> correct. Didn't check the rotor. Dumb Ass parts man gave
> me a GM rotor. Fortunally I had an old rotor that was still
> OK.
> Got everything back together and decided to adjust
> the valves. (Have Harlin Sharp Roller Rockers and screw in
> studs on this 4 barrel Cleveland). Released the rocker,
> gently tightened the nut until the pushrod could not be rotated
> with gentle finger pressure, then took one more full turn of the
> nut and locked it with the allen screw. I believed that I had
> had the motor rotated properly for each valve adjustment.
> Back together with eyeballed timing of the distributor
> and started it up. Ran like crap. Kept it running until it
> started warming up . My wife came out and said " What is that
> dripping under the Tiger?". Shut it off looked under, Had the
> Tiger up on Jack stands) lots and lots of liquid. Assumed that
> the rear of the oil pan was leaking until I smelled the fluid.
> GASOLINE, about a couple of quarts was on the floor and more was
> dripping on the now hot headers! Fortunally I was able to mop
> up the mess without burning down the Tiger, garage and house in
> that order. I have a fire extingusher in the garage and it is fairly
> big, but that much gasoline would have been a lost cause if
> it had ignited.
> Turns out that the less than year old 3/8" steel fuel line
> had rubbed on the aluminum intake and wore a hole through the
> tubing. Not a mark on the aluminum manifold. I assume that the
> vibrations due to the Holly Red fuel pumping caused the tubing
> to vibriate continiously at that point. Fixed that problem.
> Adjusted the timing to 10 before and the Tiger had very rough idle.
> I assumed that the backfire that I had previously
> experienced on acceleration was due to the need for more
> fuel. I have a 650 double pumper with pink accelerator pump
> cams. I remounted the cam to the #3 position. ( which I now
> believe to to be wrong with even less pump shot) All the other
> cams have 2 holes and #2 provides a bigger shot of fuel than #1
> which is the normal factory setting. On this cam the fuel map
> for the # 2 position was not in the Holly book. Probably
> will change to position 2 as soon as I can. Of course this
> working on the carb messed up my throttle linkage so a few hours
> working on that.
> Drove to work Monday and the Tiger was VERY rough.
> Soft backfire through the tail pipes even when I just barely
> accelerated. Held up traffic I was so slow.
> Last night did a "short the plug test" and found that
> #1 and #6 cylinder had no effect on the running. Plug on #6
> had an open circuit and plug #1 was shorted. Replaced the plugs
> and still no luck. Did a compression test and found zero pounds
> on number 1, all others were 170 to 180 psi. Re adjusted the
> valves on #1 and got 175 psi. Idle nice and smooth now.
> About to go to work on Tuesday, wish me luck.
>
>
>
>
> James Barrett Tiger II 351C and others
|