My California '74 doesn't require an air pump. Three cheers for that. And I
am guessing that the weight difference is minimal, whichever way it goes. I
used Pauls idea of the barbque paint, thanks Paul. I re-used the stock metal
from my disintigrated original valences and new hardware to hold them to the
new valences.
Your idea for the air pump sounds like a good one. That is what I would have
done.
Rob
---------- Original Text ----------
From: "alemen@pop.ftconnect.com" <alemen@pop.ftconnect.com>, on 07/05/2000
2:20 PM:
Rob, I guess it's up to what you can get and what tools you have. I don't
have a torch so that one's out, but I have heard of that type of technique
before. I saw that Paul does not have an air pump bump (as at sometime it was
removed). Do you and if so what did you do. Sounds like you may not have an
air pump due to the heavier material you used. I was considering using
aluminium flashing (as a sandwich with a thin hardboard) and making the bump
out of the flashing and riveting it on.
Alan
Original Message:
-----------------
From: rtgetzinger@scif.com
Date: Wed, 5 Jul 2000 13:56:05 PDT
Subject: Re: Engine valances
Mine were made using 1/4 inch veneer. I used a propane torch, lightly brushed
the flame to the wood, to bring out the grain on the outer facing sides and
used a marine varnish to make them look very nice as well as seal them. On
the inner facing side I used a high temp barbque black paint and just a touch
of the varnish to seal. They look really great and don't seem to mind the
heat from the headers.
Rob
---------- Original Text ----------
From: "wizardz" <wizardz@maxinter.net>, on 07/05/2000 1:38 PM:
It's just a trade name. It's basically the same stuff....
unperforated peg board.
I use the 'templates' that are floating around the web, but they didn't fit
quite right.
Make a set by the 'templates'... but out of cheap cardboard,
Once you've finished trimming to fit (and taping in add on pieces)
trace it onto your board and cut it out.
You can see one of the set I've made at
http://www.teglerizer.com/triumphstuff/v_engine.htm
The gold colored edging on the panels (top edging) is actually
wall to wall carpet edging I trimmed down. Once the panels were
cut out I spray painted them with outdoor bar-b-que grill paint.
The flat black color gives a very nice contrast, and makes the
panels look like the original cardboard.
Paul Tegler wizardz@toad.net http://www.teglerizer.com (new layout)
-----Original Message-----
From: alemen@pop.ftconnect.com <alemen@pop.ftconnect.com>
To: spitfires@autox.team.net <spitfires@autox.team.net>
Date: Wednesday, July 05, 2000 4:14 PM
Subject: Engine valances
Folks I plan to make some new ones before the old ones complety disintegrate.
They are still usable as templates.
I have seen the various plans on the web. But what is masonite (forgive the
ignorance of an exile). All I can find is hardboard like we had back in the
UK. Are hardboard and masonite the same? If noit where can I find it. The
local DIY places only have hardboard.
Alan
-------------------------------------------------------------------
This message has been posted from Mail2Web http://www.mail2web.com/
Web Hosting for $9.95 per month! Visit: http://www.yourhosting.com/
-------------------------------------------------------------------
-------------------------------------------------------------------
This message has been posted from Mail2Web http://www.mail2web.com/
Web Hosting for $9.95 per month! Visit: http://www.yourhosting.com/
-------------------------------------------------------------------
|