This is a multipart message in MIME format.
--===============3369697988388453805==
boundary="----=_NextPart_000_0001_01D6B6BD.7AD10080"
Content-Language: nl
This is a multipart message in MIME format.
------=_NextPart_000_0001_01D6B6BD.7AD10080
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
So here=E2=80=99s the story completed.
The tank was emptied enough to get the fuel pump off.
So I replaced the contact points and had these adjusted.
Also replaced the membrane and gasket.
Before assembling it all, I thoroughly cleaned and flattened the flanges, w=
here between the new membrane and gasket were to be tight.
This went well and the pump is in good working order again.
Next job is the slow starter motor.
I already cleaned the battery posts clamps and the post of the battery to c=
hassis cable.
Also cleaned thoroughly the chassis to engine cable.
Nothing helped so far.
So next will be verifying the battery voltage when cranking. I assume it wi=
ll be o.k. as the battery is new.
Following step will be measuring the voltage over the starter motor +12V to=
the engine.
When o.k., the starter is suspect. As it never was overhauled, this is logi=
cal.
Nice winter job.
Cheers,
Hans
71 BGT
Van: Mgs <mgs-bounces@autox.team.net> Namens Dan DiBiase
Verzonden: donderdag 22 oktober 2020 22:26
Aan: Richard Lindsay <richardolindsay@gmail.com>
CC: mglist <mgs@autox.team.net>; MGB-Yahoo <mg-mgb@yahoogroups.com>
Onderwerp: Re: [Mgs] Siphoning Gas
OMG, duh! Thanks to all that replied with this excellent (and obvious, now!=
) advice..............................
Dan D
http://dandibiase.cbintouch.com/
On Thu, Oct 22, 2020 at 4:13 PM Richard Lindsay <richardolindsay@gmail.com =
I had the same problem. I disconnected the fuel hose, added a a long bit of=
hose and with the coil disconnected, used the fuel pump to pump old fuel i=
nto jugs.
n.dibiase@gmail.com> > wrote:
Hi all.... My '76B, which was off the road for 5 years, was recently return=
ed to me from the shop. They added some new gas but did not siphon out the =
5 year old gas (which was just under 1/2 tank when I had it towed in. The c=
ar is running pretty rough so I want to siphon out most of the gas before I=
fill it up. It is currently showing as just under 1/2 tank, so around 6 ga=
llons or a little less (assuming gauge accuracy).
I was able to pump out about 2 gallons but am wondering if the interior of =
the tank is baffled, as I can't seem to move the hose beyond a certain area=
and it's not sucking up any additional gas. Would really like to remove a =
couple more gallons before I fill it up.
Thx,
Dan D
'76B- Getting There
'65B - Waiting It's Turn
Central NJ USA
http://dandibiase.cbintouch.com/
_______________________________________________
Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/richardolindsay@gmai=
l.com
--
Dit e-mailbericht is gecontroleerd op virussen met Avast antivirussoftware.=
https://www.avast.com/antivirus
------=_NextPart_000_0001_01D6B6BD.7AD10080
charset="utf-8"
Content-Transfer-Encoding: quoted-printable
<html xmlns:v=3D"urn:schemas-microsoft-com:vml" xmlns:o=3D"urn:schemas-micr=
osoft-com:office:office" xmlns:w=3D"urn:schemas-microsoft-com:office:word" =
xmlns:m=3D"http://schemas.microsoft.com/office/2004/12/omml" xmlns=3D"http:=
//www.w3.org/TR/REC-html40"><head><meta http-equiv=3DContent-Type content=
=3D"text/html; charset=3Dutf-8"><meta name=3DGenerator content=3D"Microsoft=
Word 15 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0cm;
font-size:11.0pt;
font-family:"Calibri",sans-serif;}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
span.E-mailStijl18
{mso-style-type:personal-reply;
font-family:"Calibri",sans-serif;
color:windowtext;}
=2EMsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri",sans-serif;
mso-fareast-language:EN-US;}
@page WordSection1
{size:612.0pt 792.0pt;
margin:70.85pt 70.85pt 70.85pt 70.85pt;}
div.WordSection1
{page:WordSection1;}
--></style><!--[if gte mso 9]><xml>
<o:shapedefaults v:ext=3D"edit" spidmax=3D"1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext=3D"edit">
<o:idmap v:ext=3D"edit" data=3D"1" />
</o:shapelayout></xml><![endif]--></head><body lang=3DNL link=3Dblue vlink=
=3Dpurple style=3D'word-wrap:break-word'><div class=3DWordSection1><p class=
=3DMsoNormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>So her=
e=E2=80=99s the story completed.<o:p></o:p></span></p><p class=3DMsoNormal>=
<span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>The tank was emptie=
d enough to get the fuel pump off.<o:p></o:p></span></p><p class=3DMsoNorma=
l><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>So I replaced the=
contact points and had these adjusted.<o:p></o:p></span></p><p class=3DMso=
Normal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>Also replace=
d the membrane and gasket.<o:p></o:p></span></p><p class=3DMsoNormal><span =
lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>Before assembling it all,=
I thoroughly cleaned and flattened the flanges, where between the new memb=
rane and gasket were to be tight. <o:p></o:p></span></p><p class=3DMsoNorma=
l><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>This went well an=
d the pump is in good working order again. <o:p></o:p></span></p><p class=
=3DMsoNormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'><o:p>&=
nbsp;</o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB style=3D'mso-=
fareast-language:EN-US'>Next job is the slow starter motor. <o:p></o:p></sp=
an></p><p class=3DMsoNormal><span lang=3DEN-GB style=3D'mso-fareast-languag=
e:EN-US'>I already cleaned the battery posts clamps and the post of the bat=
tery to chassis cable.<o:p></o:p></span></p><p class=3DMsoNormal><span lang=
=3DEN-GB style=3D'mso-fareast-language:EN-US'>Also cleaned thoroughly the c=
hassis to engine cable. <o:p></o:p></span></p><p class=3DMsoNormal><span la=
ng=3DEN-GB style=3D'mso-fareast-language:EN-US'>Nothing helped so far.<o:p>=
</o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB style=3D'mso-farea=
st-language:EN-US'>So next will be verifying the battery voltage when crank=
ing. I assume it will be o.k. as the battery is new.<o:p></o:p></span></p><=
p class=3DMsoNormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'=
>Following step will be measuring the voltage over the starter motor +12V t=
o the engine.<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB =
style=3D'mso-fareast-language:EN-US'>When o.k., the starter is suspect. As =
it never was overhauled, this is logical.<o:p></o:p></span></p><p class=3DM=
soNormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>Nice winte=
r job.<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB style=
=3D'mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=3DMsoN=
ormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'>Cheers,<o:p><=
/o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB style=3D'mso-fareas=
t-language:EN-US'>Hans<o:p></o:p></span></p><p class=3DMsoNormal><span lang=
=3DEN-GB style=3D'mso-fareast-language:EN-US'><o:p> </o:p></span></p><=
p class=3DMsoNormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'=
>71 BGT<o:p></o:p></span></p><p class=3DMsoNormal><span lang=3DEN-GB style=
=3D'mso-fareast-language:EN-US'><o:p> </o:p></span></p><p class=3DMsoN=
ormal><span lang=3DEN-GB style=3D'mso-fareast-language:EN-US'><o:p> </=
o:p></span></p><div style=3D'border:none;border-top:solid #E1E1E1 1.0pt;pad=
ding:3.0pt 0cm 0cm 0cm'><p class=3DMsoNormal><b>Van:</b> Mgs <mgs-bounce=
s@autox.team.net> <b>Namens </b>Dan DiBiase<br><b>Verzonden:</b> donderd=
ag 22 oktober 2020 22:26<br><b>Aan:</b> Richard Lindsay <richardolindsay=
@gmail.com><br><b>CC:</b> mglist <mgs@autox.team.net>; MGB-Yahoo &=
lt;mg-mgb@yahoogroups.com><br><b>Onderwerp:</b> Re: [Mgs] Siphoning Gas<=
o:p></o:p></p></div><p class=3DMsoNormal><o:p> </o:p></p><div><p class=
=3DMsoNormal>OMG, duh! Thanks to all that replied with this excellent (and =
obvious, now!) advice..............................<o:p></o:p></p><div><p c=
lass=3DMsoNormal><o:p> </o:p></p></div><div><p class=3DMsoNormal>Dan D=
<br clear=3Dall><o:p></o:p></p><div><div><div><p class=3DMsoNormal><a href=
=3D"http://dandibiase.cbintouch.com/" target=3D"_blank">http://dandibiase.c=
bintouch.com/</a><o:p></o:p></p></div></div></div><p class=3DMsoNormal><o:p=
> </o:p></p></div></div><p class=3DMsoNormal><o:p> </o:p></p><div=
><div><p class=3DMsoNormal>On Thu, Oct 22, 2020 at 4:13 PM Richard Lindsay =
<<a href=3D"mailto:richardolindsay@gmail.com">richardolindsay@gmail.com<=
/a>> wrote:<o:p></o:p></p></div><blockquote style=3D'border:none;border-=
left:solid #CCCCCC 1.0pt;padding:0cm 0cm 0cm 6.0pt;margin-left:4.8pt;margin=
-right:0cm'><div><p class=3DMsoNormal>I had the same problem. I disconnecte=
d the fuel hose, added a a long bit of hose and with the coil disconnected,=
used the fuel pump to pump old fuel into jugs.<o:p></o:p></p></div><p clas=
s=3DMsoNormal><o:p> </o:p></p><div><div><p class=3DMsoNormal>On Thu, O=
ct 22, 2020, 3:02 PM Dan DiBiase <<a href=3D"mailto:dan.dibiase@gmail.co=
m" target=3D"_blank">dan.dibiase@gmail.com</a>> wrote:<o:p></o:p></p></d=
iv><blockquote style=3D'border:none;border-left:solid #CCCCCC 1.0pt;padding=
:0cm 0cm 0cm 6.0pt;margin-left:4.8pt;margin-right:0cm'><div><p class=3DMsoN=
ormal>Hi all.... My '76B, which was off the road for 5 years, was rece=
ntly returned to me from the shop. They added some new gas but did not siph=
on out the 5 year old gas (which was just under 1/2 tank when I had it towe=
d in. The car is running pretty rough so I want to siphon out most of the g=
as before I fill it up. It is currently showing as just under 1/2 tank, so =
around 6 gallons or a little less (assuming gauge accuracy). <o:p></o:=
p></p><div><p class=3DMsoNormal><o:p> </o:p></p></div><div><p class=3D=
MsoNormal>I was able to pump out about 2 gallons but am wondering if the in=
terior of the tank is baffled, as I can't seem to move the hose beyond a ce=
rtain area and it's not sucking up any additional gas. Would really like to=
remove a couple more gallons before I fill it up.<o:p></o:p></p></div><div=
><p class=3DMsoNormal><o:p> </o:p></p></div><div><p class=3DMsoNormal>=
Thx, <o:p></o:p></p></div><div><p class=3DMsoNormal><o:p> </o:p><=
/p></div><div><p class=3DMsoNormal>Dan D<o:p></o:p></p></div><div><p class=
=3DMsoNormal>'76B- Getting There<o:p></o:p></p></div><div><p class=3D=
MsoNormal>'65B - Waiting It's Turn<o:p></o:p></p></div><div><p class=3DMsoN=
ormal>Central NJ USA<br clear=3Dall><o:p></o:p></p><div><div><div><p class=
=3DMsoNormal><a href=3D"http://dandibiase.cbintouch.com/" target=3D"_blank"=
>http://dandibiase.cbintouch.com/</a><o:p></o:p></p></div></div></div></div=
></div><p class=3DMsoNormal>_______________________________________________=
<br><br><a href=3D"mailto:Mgs@autox.team.net" target=3D"_blank">Mgs@autox.t=
eam.net</a><br>Donate: <a href=3D"http://www.team.net/donate.html" target=
=3D"_blank">http://www.team.net/donate.html</a><br>Suggested annual donatio=
n $12.75<br><br>Archive: <a href=3D"http://www.team.net/pipermail/mgs=
" target=3D"_blank">http://www.team.net/pipermail/mgs</a> <a href=3D"http:/=
/autox.team.net/archive" target=3D"_blank">http://autox.team.net/archive</a=
><br><br>Unsubscribe: <a href=3D"http://autox.team.net/mailman/options/mgs/=
richardolindsay@gmail.com" target=3D"_blank">http://autox.team.net/mailman/=
options/mgs/richardolindsay@gmail.com</a><o:p></o:p></p></blockquote></div>=
</blockquote></div></div><div id=3D"DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2"><=
br /> <table style=3D"border-top: 1px solid #D3D4DE;">
<tr>
<td style=3D"width: 55px; padding-top: 18px;"><a href=3D"https://www.=
avast.com/sig-email?utm_medium=3Demail&utm_source=3Dlink&utm_campaign=3Dsig=
-email&utm_content=3Demailclient" target=3D"_blank"><img src=3D"https://ipm=
cdn.avast.com/images/icons/icon-envelope-tick-round-orange-animated-no-repe=
at-v1.gif" alt=3D"" width=3D"46" height=3D"29" style=3D"width: 46px; height=
: 29px;" /></a></td>
<td style=3D"width: 470px; padding-top: 17px; color: #41424e;
font-size: =
13px; font-family: Arial, Helvetica, sans-serif; line-height: 18px;">Virusv=
rij. <a href=3D"https://www.avast.com/sig-email?utm_medium=3Demail&utm_sour=
ce=3Dlink&utm_campaign=3Dsig-email&utm_content=3Demailclient" target=3D"_bl=
ank" style=3D"color: #4453ea;">www.avast.com</a> </td>
</tr>
</table>
<a href=3D"#DAB4FAD8-2DD7-40BB-A1B8-4E2AA1F9FDF2" width=3D"1" height=3D"1">=
</a></div></body></html>
------=_NextPart_000_0001_01D6B6BD.7AD10080--
--===============3369697988388453805==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Mgs@autox.team.net
Archive: http://www.team.net/pipermail/mgs http://autox.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/mharc@autox.team.net
--===============3369697988388453805==--
|