--===============8307763890042621906==
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div style=3D"font-family: Verdana;font-size: 12=
=2E0px;"><div>This is how to determine where to put your antenna=2E</div>
<div> </div>
<div>Locate a portable radio, one with medium wave reception=2E</div>
<div>Tune to a medium wave transmitter=2E (if you can find one)=2E</div>
<div>Start the car engine=2E </div>
<div>Walk around the car with the radio near your considered antenna =
locations=2E</div>
<div> </div>
<div>The best location is obviously where you hear minimal ignition noise =
on your radio=2E</div>
<div> </div>
<div>Bert</div>
<div> </div>
<div>PA0LPS</div>
<div>SA4BRL</div>
<div> </div>
<div> </div>
<div>
<div name=3D"quote" style=3D"margin:10px 5px 5px 10px; padding: 10px 0 10p=
x 10px; border-left:2px solid #C3D9E5; word-wrap: break-word; -webkit-nbsp-=
mode: space; -webkit-line-break: after-white-space;">
<div style=3D"margin:0 0 10px 0;"><b>Gesendet:</b> Montag, 20=2E Juni=
2016 um 23:58 Uhr<br/>
<b>Von:</b> "Steve via Mgs" <mgs@autox=2Eteam=2Enet><=
br/>
<b>An:</b> "mgs@autox=2Eteam=2Enet" <mgs@autox=2Eteam=2E=
net><br/>
<b>Betreff:</b> [Mgs] Antenna hole size on MGB</div>
<div name=3D"quoted-content">I also have to wonder why you want to put the=
antenna on driver's side=2E I too would put it on the passenger's =
side=2E Unless you are talking about the rear=2E Still? As for size of hole=
, measure the metal part that goes through the fender or scuttle into the c=
ar, (it's usually some sort of threaded cast metal)=2E You must use the=
actual antenna you are going to install=2E The part that is to go through =
the fender may not be circular, but you can extrapolate the circle from the=
size=2E The antenna may also have instructions=2E Hmm=2E As a rough estima=
te you can use the chrome bezel of the antenna as a guess=2E You don't =
want to make the hole larger than that=2E In fact, you want to make the hol=
e as small as possible=2E You may be able to install the workings of the an=
tenna from the inside of the car=2E Make a template of the hole you want to=
make=2E Again, don't make it bigger than the chrome bezel of the anten=
na=2E Make sure that there isn't something important under the location=
where you are going to drill<br/>
the hole, and that you will have enough room in the footwell, fender, etc=
=2E for the antenna motor and shaft and will be able to snake the wire thro=
ugh to the radio=2E Find your location, tape your template on so both sides=
of the cut are protected=2E I suggest using a pinpoint metal punch to dimp=
le the center of the hole to be cut, then employ a new circular metal cutti=
ng blade with small center pilot hole=2E Insert the bit into VSR drill, hav=
e a beer, grit your teeth, and go for it=2E<br/>
Any problems, have another beer and ask a neighbor for HELP!<br/>
<br/>
Steve Edelstein<br/>
Sent from my iPad<br/>
_______________________________________________<br/>
<br/>
Mgs@autox=2Eteam=2Enet<br/>
">http://www=2Eteam=2Enet/donate=2Ehtml</a><br/>
Archive: <a href=3D"http://www=2Eteam=2Enet/archive"; target=3D"_blank">htt=
p://www=2Eteam=2Enet/archive</a><br/>
Forums: <a href=3D"http://www=2Eteam=2Enet/forums"; target=3D"_blank">http:=
//www=2Eteam=2Enet/forums</a><br/>
Unsubscribe: <a href=3D"http://autox=2Eteam=2Enet/mailman/options/mgs/palt=
e@gmx=2Enet" target=3D"_blank">http://autox=2Eteam=2Enet/mailman/options/mg=
s/palte@gmx=2Enet</a></div>
</div>
</div></div></body></html>
--===============8307763890042621906==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Mgs@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/mgs/mharc@autox.team.net
--===============8307763890042621906==--
|