--===============6467895672004197293==
--0000000000008cf0a805e05bae28
Hi Shawn -
The "superdry" seals need to be used with updated jet bearings as well....
the old style jet bearings will only work with cork seals, you cant put
rubber seals in it's place. You have to buy them as a unit. I have zero
problems with leaky H4s.
https://sucarb.co.uk/carburettor-kits/jet-bearing-kits/h-type-carburettors/h-type-superdry-jet-bearing-seal-kit.html
Best,
Alan
On Tue, May 31, 2022 at 9:50 PM S and T Miller <stmiller96@hotmail.com>
wrote:
> Anyone come up with any good tricks to seal the jets from leaking, and
> stay centered? I chamfered the jet side holes so not to tear the "upgraded"
> o-rings but still seeps fuel. Tried three sets with with no success. Also
> the jet bearing doesn't seem to stay centered and it's easy to move the jet
> assembly around from underneath. I stretched out the old gland springs and
> that seemed to help, so I installed new gland springs and still not great.
> Thinking of stretching out the new gland springs and use new oil soaked
> cork seals, as original. Thoughts?
> TIA, Shawn
>
> The Millers
>
> "Always drive them, but remember each drive in an antique car is a test
> drive."
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive/healeys
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/healey.nut@gmail.com
>
>
--0000000000008cf0a805e05bae28
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr">Hi Shawn -<div><br></div><div>The "superdry" sea=
ls need to be used with updated jet bearings as well.... the old style jet =
bearings will only work with cork seals, you cant=C2=A0put rubber seals in =
it's place.=C2=A0 You have to buy them as a unit.=C2=A0 I have zero pro=
blems with leaky H4s.<br><br><a href=3D"https://sucarb.co.uk/carburettor-ki=
ts/jet-bearing-kits/h-type-carburettors/h-type-superdry-jet-bearing-seal-ki=
t.html">https://sucarb.co.uk/carburettor-kits/jet-bearing-kits/h-type-carbu=
rettors/h-type-superdry-jet-bearing-seal-kit.html</a><br></div><div><br></d=
iv><div>Best,</div><div><br></div><div>Alan</div></div><br><div class=3D"gm=
ail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Tue, May 31, 2022 at 9:=
50 PM S and T Miller <<a href=3D"mailto:stmiller96@hotmail.com";>stmiller=
96@hotmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quote" st=
yle=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padd=
ing-left:1ex">
<div>
<div style=3D"font-family:inherit;font-size:inherit;color:inherit">Anyone c=
ome up with any good tricks to seal the jets from leaking, and stay centere=
d? I chamfered the jet side holes so not to tear the "upgraded" o=
-rings but still seeps fuel. Tried three
sets with with no success. Also the jet bearing doesn't seem to stay c=
entered and it's easy to move the jet assembly around from underneath.=
=C2=A0 I stretched out the old gland springs and that seemed to help, so I =
installed new gland springs and still not great.
Thinking of stretching out the new gland springs and use new oil soaked co=
rk seals, as original.=C2=A0 Thoughts?</div>
<div style=3D"font-family:inherit;font-size:inherit;color:inherit">TIA, Sha=
wn</div>
<div><br>
</div>
<div>The Millers<br>
=C2=A0<br>
"Always drive them, but remember each drive in an antique car is a tes=
t drive."<br>
</div>
</div>
_______________________________________________<br>
rer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <a href=3D"h=
ttp://autox.team.net/archive/healeys" rel=3D"noreferrer" target=3D"_blank">=
http://autox.team.net/archive/healeys</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank">Healeys@autox.t=
eam.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
s/healey.nut@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://autox.t=
eam.net/mailman/options/healeys/healey.nut@gmail.com</a><br>
<br>
</blockquote></div>
--0000000000008cf0a805e05bae28--
--===============6467895672004197293==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys
http://autox.team.net/archive/healeys
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============6467895672004197293==--
|