--===============8572833912188998001==
--000000000000f8399605994c77fb
Hi Michael,
I encountered the same issue with the early dash in B.#174. After a bit of
adjustment I managed to get the 2 holes essentially concentric and just
squeeze the light body into the gap.
Not easy once the dash is installed I might mention!!
M
On Mon, Dec 9, 2019 at 12:48 PM Michael MacLean <rrengineer.mike@att.net>
wrote:
> In retrofitting an early two piece dash to my BN2 I have run into a snag
> with the turn signal indicator light assembly. The light assembly I bought
> from one of the usual suspects is a two piece affair. It has a very nice
> external threaded chrome bezel and an internal threaded green tube with a
> sort of lens coming up through the center and protruding into the bezel.
> This would be fine if it was mounted to a one piece dash, but as you can
> see in the picture the mounting hole is not centered in relation to the
> sheet metal above and behind the instrument panel. Easy enough, just grind
> away until it fits. This brings up another question. If I didn't want to
> bugger up an original early two piece dash, what did the early light
> bulbholder fitting that would fit here look like?
> Mike MacLean
>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
> http://autox.team.net/archive
>
> Healeys@autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/michaelsalter@gmail.com
>
>
--000000000000f8399605994c77fb
Content-Transfer-Encoding: quoted-printable
<div dir=3D"ltr"><div class=3D"gmail_default" style=3D"font-family:comic sa=
ns ms,sans-serif;font-size:small">Hi Michael,</div><div class=3D"gmail_defa=
ult" style=3D"font-family:comic sans ms,sans-serif;font-size:small">I encou=
ntered the same issue with the early dash in B.#174. After a bit of=C2=A0
adjustment I managed to get the 2 holes essentially concentric and just squ=
eeze the light body into the gap.</div><div class=3D"gmail_default" style=
=3D"font-family:comic sans ms,sans-serif;font-size:small"><br></div><div cl=
ass=3D"gmail_default" style=3D"font-family:comic sans ms,sans-serif;font-si=
ze:small">Not easy once the dash is installed I might mention!!</div><div c=
lass=3D"gmail_default" style=3D"font-family:comic sans ms,sans-serif;font-s=
ize:small"><br></div><div class=3D"gmail_default" style=3D"font-family:comi=
c sans ms,sans-serif;font-size:small">M<br></div></div><br><div class=3D"gm=
ail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Mon, Dec 9, 2019 at 12:=
48 PM Michael MacLean <<a href=3D"mailto:rrengineer.mike@att.net";>rrengi=
neer.mike@att.net</a>> wrote:<br></div><blockquote class=3D"gmail_quote"=
style=3D"margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);p=
adding-left:1ex"><div><div style=3D"font-family:times new roman,new york,ti=
mes,serif;font-size:16px"><div dir=3D"ltr"><div dir=3D"ltr">In retrofitting=
an early two piece dash to my BN2 I have run into a snag
with the turn signal indicator light assembly.=C2=A0 The light assembly I =
bought from one of=20
the usual suspects is a two piece affair.=C2=A0 It has a very nice external=
threaded chrome=20
bezel and an internal threaded green tube with a sort of lens coming up thr=
ough the center=20
and protruding into the bezel.=C2=A0 This would be fine if it was mounted t=
o a
one piece dash, but as you can see in the picture the mounting hole is=20
not centered in relation to the sheet metal above and behind the instrument=
=20
panel.=C2=A0 Easy enough, just grind away until it fits.=C2=A0 This brings =
up=20
another question.=C2=A0 If I didn't want to bugger up an original early=
two piece dash, what did the early light bulbholder fitting that would fit=
here
look like?</div><div>Mike MacLean</div><div><br></div></div></div></div>__=
_____________________________________________<br>
rer" target=3D"_blank">http://www.team.net/donate.html</a><br>
<br>
Archive: <a href=3D"http://www.team.net/pipermail/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://www.team.net/pipermail/healeys</a> <a href=3D"h=
ttp://autox.team.net/archive" rel=3D"noreferrer" target=3D"_blank">http://a=
utox.team.net/archive</a><br>
<br>
<a href=3D"mailto:Healeys@autox.team.net"; target=3D"_blank">Healeys@autox.t=
eam.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/healeys"; rel=3D"noreferre=
r" target=3D"_blank">http://autox.team.net/mailman/listinfo/healeys</a><br>
<br>
s/michaelsalter@gmail.com" rel=3D"noreferrer" target=3D"_blank">http://auto=
x.team.net/mailman/options/healeys/michaelsalter@gmail.com</a><br>
<br>
</blockquote></div>
--000000000000f8399605994c77fb--
--===============8572833912188998001==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/pipermail/healeys http://autox.team.net/archive
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
--===============8572833912188998001==--
|