Great
Ira Erbs
Portland, OR
typos and artifacts are the fault of my phone
On Wed, Jul 4, 2018, 5:10 PM Bob Haskell <rchaskell at earthlink.net> wrote:
> All,
>
> To paraphrase a summer saying: "It's not the heat, it's the stupidity".
> The spin-on adapter was upside down. It now has "TOP" stamped on it, in
> an attempt to save me from myself in the future.
>
> When in doubt, read the instructions. I have a couple of extra adapters
> (with instructions) that I bought at Jack Summer's estate sale. The
> 1/2" drilling between the two counterbored holes goes at the bottom.
> Thanks Jack.
>
> Oil pressure is about 60 psi cold. I guess 90 degrees is considered cold.
>
> Thanks for all your assistance.
>
> Cheers,
>
> Bob Haskell
> AHCA 3000 MkI registrar
> http://www.ciahc.org/registry_3000mk1.php
>
> On 07/03/2018 11:46 PM, Engl wrote:
> > Bob
> >
> > Something you indicated in your note seemed odd to me. That being the
> filter ?popped? when you loosened it. This is not something I have
> encountered before; is it normal? If not normal, something seems plugged
> downstream of the filter allowing pressure to build-up and stay in the oil
> system. If the oil galleries diverge immediately downstream of the filter,
> the culprit is most likely in the immediate vicinity of the filter. The
> first thing would be to check the spin-on filter adapter as others have
> suggested.
> >
> > Bob England
> >
> >> On Jul 3, 2018, at 6:44 PM, Bob Haskell <rchaskell at earthlink.net>
> wrote:
> >>
> >> All,
> >>
> >> The pump does work. I typically fill the oil filter before installing
> it. I took the filter off and install a new one dry. Spun the engine on
> the starter for 20 seconds or so and removed the filter. It had oil in
> it. There was still pressure in the system and it "popped" as I loosened
> the filter.
> >>
> >> Still no oil pressure at the gauge or oil at the rocker arms.
> >>
> >> With the filter removed, I can stick a depth gauge about an inch into
> the engine block (both inlet and outlet). As installed, the filter inlet
> hole is at about 10 o'clock right now. I don't think that the adapter can
> be installed so just one hole blocked, but I'll remove it to confirm it's
> on correctly. It's easy enough to do.
> >>
> >> The oil path divides after leaving the filter, one to the rocker shaft
> and one to the main bearings. The gauge is on the latter. Not seeing oil
> on either path seems to point to the filter/adapter.
> >>
> >> Back to the garage.
> >>
> >> Thanks.
> >>
> >> Cheers,
> >>
> >> Bob Haskell
> >> AHCA 3000 MkI registrar
> >> http://www.ciahc.org/registry_3000mk1.php
> >>
> >>> On 07/03/2018 07:42 PM, i erbs wrote:
> >>> Is soon on adaptors on correctly and not blocking feed holes?
> >>> Ira Erbs
> >>> Portland, OR
> >>> typos and artifacts are the fault of my phone
> >>> On Tue, Jul 3, 2018, 6:24 PM Bob Haskell <rchaskell at earthlink.net
> >>> All,
> >>> Pulled the engine out of our tri-carb last December due to low oil
> >>> pressure and running too hot. Bearings were okay; the engine got
> a new
> >>> oil pump, rear main seal, pressure relief spring and plunger, and
> >>> timing
> >>> gears, chain and tensioner.
> >>> Started the engine yesterday and it started almost immediately.
> So I
> >>> was really pleased until I looked at the oil pressure gauge and
> saw the
> >>> needle was sitting on the peg. No oil visible at the rocker arms
> >>> either.
> >>> I removed the spin on oil filter and attempted to prime the oil
> pump by
> >>> squirting oil the filter inlet passage. But it was already full.
> >>> Can one remove the distributor and spin the oil pump with a drill
> >>> motor?
> >>> I'd like to be able to test without spinning the crank and cam
> on
> >>> dry
> >>> bearings, etc..
> >>> Suggestions?
> >>> Cheers,
> >>> Bob Haskell
> >>> AHCA 3000 MkI registrar
> >>> http://www.ciahc.org/registry_3000mk1.php
> >>> _______________________________________________
> >>> Support Team.Net http://www.team.net/donate.html
> >>> Suggested annual donation $12.75
> >>> Archive: http://www.team.net/pipermail/healeys
> >>> http://autox.team.net/mailman/listinfo/healeys
> >>> Unsubscribe/Manage:
> >>> http://autox.team.net/mailman/options/healeys/eyera3000 at gmail.com
> >> _______________________________________________
> >> Support Team.Net http://www.team.net/donate.html
> >> Suggested annual donation $12.75
> >>
> >> Archive: http://www.team.net/pipermail/healeys
> >>
> >> Healeys at autox.team.net
> >> http://autox.team.net/mailman/listinfo/healeys
> >>
> >> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/engl at accesscomm.ca
> >>
> >
> >
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.75
>
> Archive: http://www.team.net/pipermail/healeys
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/listinfo/healeys
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/healeys/eyera3000 at gmail.com
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20180704/b7c66ae2/attachment.html>
|