Good info Curt, this is such a great list. I was going to Star for the rebuild
and thought it would be better if I went with the replacement parts in hand. I
need both ends but the car is nowhere near 100 points so anything close will
look OK. I am about to get all over e-bay with the info you have provided. Much
thanks to all who responded to my request.
Thanks you guysRay Juncal
From: Curtis Arndt <cnaarndt at gmail.com>
To: Tom Felts <tomfelts at windstream.net>; Ray Juncal <healeyray at
yahoo.com>
Cc: Oudesluys <coudesluijs at chello.nl>; Healey List <healeys at
autox.team.net>
Sent: Tuesday, October 10, 2017 5:31 PM
Subject: Re: [Healeys] Generators
Ray
The number cast into the bracket ear on the back of bracket 239266 is 239013
(go figure?).? These typically ALL have the brass oiler on them, and the later
brackets on BN2s do not. But this is not a big deal, as I prefer the ones with
the bushing oiler.
These typically run $45 to $65 on eBay.? None listed right now but be patient.
The front bracket is "Bracket or frame, drive end" and is Lucas part no.
239012. These are a bit harder to find.
Also, have you tried the good folks at Star Auto Electric in Los Angeles?? They
should be able to fix you up.
http://www.starautoelectric.co m/
207 W Foothill Blvd
ADDRESS:
Monrovia, CA 91016
(866) 969-7827
Cheers,
CurtADDRESS:
On Tue, Oct 10, 2017 at 4:35 PM, Curtis Arndt <cnaarndt at gmail.com> wrote:
These generator end plates are quite common and I've purchased plenty of them
NOS off of eBay over the years.
You're specifically looking for a "Bracket or frame, commutator end" or try
this in an eBay search "Lucas generator commutator end plate or bracket"? NOS
good, as I find these for sale quite often.
The Lucas part no. for a 22456A/D or a 22383A/B/D generator is 239266.
Cheers,
Curt
On Tue, Oct 10, 2017 at 12:27 PM, Tom Felts <tomfelts at windstream.net> wrote:
I had mine welded? back on.
---- Oudesluys <coudesluijs at chello.nl> wrote:
=============
Fit an alternator!
Kees Oudesluijs
Op 10-10-2017 om 7:25 schreef Ray Juncal:
> I have broken mounting tabs on both front and rear end plates of my
> BN-1 generator. I want to send it out for a complete rebuild. What is
> the best way to deal with the broken end plates?? Anyone have a burned
> up generator they want to sell the end plates off of?, or how about a
> complete rebuildable four cylinder generator. What is the wisdom of
> the list?
> Thanks
> Ray Juncal
>
>
>
> ______________________________ _________________
> Support Team.Net http://www.team.net/donate.htm l
> Suggested annual donation? $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
>
> Healeys at autox.team.net
> http://autox.team.net/mailman/ listinfo/healeys
>
> Unsubscribe/Manage: http://autox.team.net/mailman/
> options/healeys/coudesluijs at ch ello.nl
>
______________________________ _________________
Archive: http://www.team.net/archive
Healeys at autox.team.net
http://autox.team.net/mailman/ listinfo/healeys
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://autox.team.net/pipermail/healeys/attachments/20171011/e81a61b8/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Generator 239266.jpg
Type: image/jpeg
Size: 4781861 bytes
Desc: not available
URL:
<http://autox.team.net/pipermail/healeys/attachments/20171011/e81a61b8/attachment-0001.jpg>
|
