Price,
I'm having trouble following your description because:
1) there should not be a 'vacuum hose' going into the stock air
filters. That is actually a (slight) pressure hose for venting
crankcase fumes back into the induction system for combustion
2) there IS a vacuum hose from the brake servo--with a check valve at
the servo or possibly fitted inline in the hose--and it should never be
installed anywhere but on the nipple on the intake manifold
3) if you want to run a vacuum line from the crankcase to the intake
manifold you need to install a PCV valve inline
Anyway, the only possible way to get fuel in the servo is from the
intake system downstream of the carburettors; if 2 cylinders were
not/mis-firing that unburned fuel would end up in the crankcase and oil
(and possibly some evaporated back into the induction system). So, yes,
some fuel could get into the servo via the vacuum line on the manifold,
but if it was more than a trace your engine would likely be flooded out.
I'm not sure what the servo rebuilder was talking about (unless you
talked to the tech that did the rebuild he could have been blowing
smoke). There is no 'baffle' in the servo; the large air/vacuum piston
has a rubber/leather seal around the perimeter, and this can get brittle
contributing to poor operation of the servo. The typical failure
mechanism--the one resulting in brake fluid being drawn into the
air/vacuum cylinder--is the aging and embrittlement of the 'gland seal,'
a small, circular rubber seal that seals the shaft of the air/vacuum
piston; on one side is manifold vacuum and on the other is the brake
fluid in the servo's 'master' cylinder.
If all your hoses, etc. are connected properly to their proper locations
I would not worry about getting fuel in the rebuilt servo.
Bob
On 12/30/2015 3:07 PM, R. Price Lindsay wrote:
> Listers -
>
> A couple of weeks ago my brakes were acting funny. It turned out that all of
> the fluid was out of the brake/clutch reservoir. I sent the brake servo into
> be repaired at the suggestion of the list. I just talked to the rebuilder
> and he said the baffle in the servo was swollen because of a large amount of
> fuel present in the booster. He mentioned this is not unusual with TR6â??s.
> I guess this can cause the servo to fail and draw the brake fluid into the
> servo.
>
> Now that the servo is fixed, I donâ??t want a repeat the problem and am
> searching for a cause for the presence of fuel. A few months ago I was
> having a problem with fuel starvation. It turned out to be a pinched fuel
> line. During my long search I made a number of changes including installing
> a new distributor cap and wires. Somehow I switched a couple of wires and
> could not get a spark in cylinders 5 & 6. I found the problem after quite a
> bit of trying to get the car to run smoothly and driving it for 20 - 30
> miles. Also, maybe a contributing factor or maybe not, a year or two ago I
> moved the vacuum hose to the induction manifold because I installed air
> cleaners without a connection point for the vacuum hose. (Before the fuel
> starvation issue I reinstalled the original air cleaners and moved the vacuum
> hose back up to the air rear cleaner.)
>
> Now for my question: Could the presence of fuel in the brake booster have
> been caused when I was not getting spark and not burning fuel in 5 & 6?
> Could the unspent fuel have been sucked into the servo through the induction
> manifold a while ago, or through the air cleaners recently?
>
> Thank you so much for your collective thoughts.
>
> Price Lindsay
> 67 BJ8
>
>
>
_______________________________________________
Support Team.Net http://www.team.net/donate.html
Suggested annual donation $12.75
Archive: http://www.team.net/archive
Forums: http://www.team.net/forums
Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys
Unsubscribe/Manage:
http://autox.team.net/mailman/options/healeys/mharc@autox.team.net
|