healeys
[Top] [All Lists]

[Healeys] petronix

Subject: [Healeys] petronix
From: coudesluijs at chello.nl (Oudesluys)
Date: Fri, 04 Nov 2011 16:04:56 +0100
References: <20111104091055.NR5O8.466983.root@pamxwww10-z01>
Bullshit.
It will function fine with most 12V 3 Ohm coils or with coils plus 
ballast resistor with a total resistance of 3+ Ohm.
Kees Oudesluijs



Op 4-11-2011 14:10, Tom Felts schreef:
> I simply don't understand.  When I bought the Pertronix I was specifically 
> told that I HAD to install a Lucus Sport Coil or it would not function 
> properly.  (??)
>
> tom
>
>
> ---- Greg Lemon<glemon at neb.rr.com>  wrote:
>
> =============
> I used a Pertronix for 10 years with a Lucas Sport coil too, no  issues,
> although I also believe I have heard the story from  more people than just
> Alan that it might not be the best mix.
>
> Saw the new Senna movie tonight, it was very good, wife even liked it. quite
> a story, quite an amazing talent.
>
> Greg Lemon
>
>
>
>
> ----- Original Message -----
> From: "Tom Felts"<tomfelts at windstream.net>
> To: "Michael MacLean"<rrengineer.mike at att.net>;<edic at tampabay.rr.com>;
> <healeys at autox.team.net>
> Sent: Thursday, November 03, 2011 8:08 PM
> Subject: Re: [Healeys] petronix
>
>
>> FWIW, I have had a Pertronix with a Lucas Sport Coil for 10 years with
>> MANY miles--once across Europe for 47 days--over 6000 miles.  Still going
>> strong with same units 10 years later.
>>
>> BJ8-----does that make a difference?
>>
>> tom
>>
>> ---- Michael MacLean<rrengineer.mike at att.net>  wrote:
>>
>> =============
>> --- On Thu, 11/3/11, Michael MacLean<rrengineer.mike at att.net>  wrote:
>>
>>
>>
>> I don't know where you get your information from Alan, but all that is
>> required for the Pertronix unit is a coil that has 3.0 ohms resistance or
>> greater.  The Lucas Sport Coil has this and I have been using one in my
>> Bugeye
>> with a Pertronix unit installed since Jeff Schlemmer rebuilt my
>> distributor 4
>> years ago.  It has been working flawlessly ever since.  I even called the
>> guys
>> at Pertronix to make sure about the coil.  They were the ones that told me
>> the
>> minimum resistance required and how to measure it on the coil.
>> Mike MacLean
>> 60 AN5
>> 56 BN2
>>
>> --- On Thu, 11/3/11, Alan Seigrist<healey.nut at gmail.com>  wrote:
>>
>> From: Alan Seigrist<healey.nut at gmail.com>
>> Subject: Re: [Healeys] petronix
>> To:
>> "edic at tampabay.rr.com"<edic at tampabay.rr.com>
>> Cc: healeys at autox.team.net
>> Date: Thursday, November 3, 2011, 1:43 PM
>>
>> Mel -
>>
>> A standard Pertronix unit is unable to handle a high energy low resistance
>> coil like the Lucas Sport Coil (common) over extended running periods.  Is
>> that what you were running?  If so, that's what burned out your Pertronix.
>>
>> You need to get a Pertronix coil with a 3 ohm internal resistance, that
>> will prevent further burnouts.
>>
>> Alan
>> _______________________________________________
>> Healeys at autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation  $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/healeys/tomfelts at windstream.net
>> _______________________________________________
>> Healeys at autox.team.net
>> Donate: http://www.team.net/donate.html
>> Suggested annual donation  $12.75
>> Archive: http://www.team.net/archive
>> Forums: http://www.team.net/forums
>> Unsubscribe/Manage:
>> http://autox.team.net/mailman/options/healeys/glemon at neb.rr.com
> _______________________________________________
> Healeys at autox.team.net
> Donate: http://www.team.net/donate.html
> Suggested annual donation  $12.75
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage: http://autox.team.net/mailman/options/healeys/coudesluijs 
> at chello.nl
>
>
> -----
> Geen virus gevonden in dit bericht.
> Gecontroleerd door AVG - www.avg.com
> Versie: 2012.0.1869 / Virusdatabase: 2092/4594 - datum van uitgifte: 11/03/11

<Prev in Thread] Current Thread [Next in Thread>