Gergo and Ira - let me add my 3good luck2message to you both. I9m aiming for
a Sept. 1st first time start up date. Then I can finally get to putting the
re-done body panels back on for the last time. Still have some chrome to get
done as well.
Tom
On 5/30/11 1:23 AM, "Austin Healey" <pajtamuvek at gmail.com> wrote:
> Good uck Ira!
>
> Gergo
>
> 2011/5/30 I Erbs <eyera3 at gmail.com>
>>
>> Almost,
>> My engine has about 35k on it over the last 35 years. Waiting to restart
>> mine, with newly rebuilt HD8 Carbs. Hopefully two weeks out to
restart.good
>> luck with your initial startup. The machine shop did a fast job.
>>
>> Ira Erbs
>> IT Consultant
>> Portland, OR
>>
>> sent from my Droid, please excuse typos and random self corrections
because
>> my phone has It's own ideas about what word I meant to write
>>
>> On May 28, 2011 11:33 PM, "Austin Healey" <pajtamuvek at gmail.com> wrote:
>>> > I am in about the same situation. Engine, transmission in, new loom
>>> wiaiting
>>> > to be installed.
>>> >
>>> > Gergo
>>> >
>>> > 2011/5/28 I Erbs <eyera3 at gmail.com>
>>> >
>>>> >> Would like to see some photos,
>>>> >> I still need to bolt down my tranny mounts and drive shaft. New wire
>>>> >> harness
>>>> >> this weekend, carbs back in two weeks, then hook up and restart car
for
>>>> >> first time in 20 months, when we started this project. Still lots to
>>>> do,
>>>> >> but a lot has been completed.
>>>> >> Good luck with recovery. Do your exercises
>>>> >>
>>>> >> Ira Erbs
>>>> >> DIGS-4 Solutions
>>>> >> Portland, OR
>>>> >>
>>>> >> sent from my Droid, please excuse typos and random self corrections
>>>> because
>>>> >> my phone has It's own ideas about what word I meant to write
>>>> >>
>>>> >> On May 27, 2011 12:04 PM, "Thomas Morrione" <tjmorrio at colby.edu>
wrote:
>>>>> >> > Ira b9 fwiw b9 I put my grommets in after I put on durmat and the
>>>> >> tarpaper.
>>>> >> It
>>>>> >> > worked ok in all but two of the cases where I didnB9t cut holes
quite
>>>> >> large
>>>>> >> > enough b9 suggest just eyeball it and see if thereB9s any
likelihood
that
>>>>> >> > youB9ll not be able to put the grommet in without more trimming. I
did
>>>> >> put
>>>>> >> > the couple of balk gromment/plugs in before I put on the duramat.
>>>>> Forgot
>>>>> >> > which those were though. Have just had knee replacement last week
and
am
>>>>> >> > laid up or would go look further.
>>>>> >> >
>>>>> >> > Have enjoyed your chronicle of rebuild b9 am about to put in
redone
>>>>> >> > engine/trans/od this summer and move my project along/
>>>>> >> >
>>>>> >> > Best,
>>>>> >> > Tom
>>>> >> _______________________________________________
>>>> >> Healeys at autox.team.net
>>>> >> Donate: http://www.team.net/donate.html
>>>> >> Suggested annual donation $12.75
>>>> >> Archive: http://www.team.net/archive
>>>> >> Forums: http://www.team.net/forums
>>>> >> Unsubscribe/Manage:
>>>> >> http://autox.team.net/mailman/options/healeys/pajtamuvek at gmail.com
|