--===============1582122926009049506==
boundary="----=_Part_1579682_1585996120.1687101272506"
------=_Part_1579682_1585996120.1687101272506
Content-Transfer-Encoding: quoted-printable
Does anyone have a complete TR-3 distributor laying around?=C2=A0 I need to=
know the dimension from the bottom of the distributor housing, where it si=
ts on the block (without the hold down clamp) to the bottom of the drive ge=
ar (ignore the 2 tabs which interface with the drive gear).
In my race car, I used a Datsun B210 electronic distributor as my backup ig=
nition.=C2=A0 Primary was a crank trigger.=C2=A0 This Datsun distributor sl=
id right into the hole in the Triumph distributor pedestal, But the shaft w=
as a little bit longer.=C2=A0 So, I had to shim it with a spacer between th=
e bottom of the distributor body, and the distributor housing.
I recently picked up a new Datsun distributor on Ebay, and I am preparing t=
o put it in my street TR-3.=C2=A0 I'm trying to get all the preparations do=
ne before I take the Lucas distributor out of my TR-3, as I drive it regula=
rly.=C2=A0 The dimension I need (above) will allow me to make up a spacer o=
f the correct thickness.
Bryan Braselton, if you read this and still have the distributor setup I ha=
d on the car, maybe you can measure the thickness of the shim between the d=
istributor and the distributor pedestal (I think it was about 5/16" thick).=
=C2=A0 That will save me from doing the calculation.=C2=A0 I have a wiring =
diagram for this electronic distributor setup if anyone is interested.=C2=
=A0 The Datsun distributor was about $65 on Ebay.
Thanks for any help you can give me with this.
Jack Wheeler
.
------=_Part_1579682_1585996120.1687101272506
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div class=3D"yahoo-style-wrap" style=3D"font-fami=
ly:Helvetica Neue, Helvetica, Arial, sans-serif;font-size:13px;"><div dir=
=3D"ltr" data-setdir=3D"false">Does anyone have a complete TR-3 distributor=
laying around? I need to know the dimension from the bottom of the d=
istributor housing, where it sits on the block (without the hold down clamp=
) to the bottom of the drive gear (ignore the 2 tabs which interface with t=
he drive gear).</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div =
dir=3D"ltr" data-setdir=3D"false">In my race car, I used a Datsun B210 elec=
tronic distributor as my backup ignition. Primary was a crank trigger=
. This Datsun distributor slid right into the hole in the Triumph dis=
tributor pedestal, But the shaft was a little bit longer. So, I had t=
o shim it with a spacer between the bottom of the distributor body, and the=
distributor housing.</div><div dir=3D"ltr" data-setdir=3D"false"><br></div=
><div dir=3D"ltr" data-setdir=3D"false">I recently picked up a new Datsun d=
istributor on Ebay, and I am preparing to put it in my street TR-3. I=
'm trying to get all the preparations done before I take the Lucas distribu=
tor out of my TR-3, as I drive it regularly. The dimension I need (ab=
ove) will allow me to make up a spacer of the correct thickness.</div><div =
dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D=
"false">Bryan Braselton, if you read this and still have the distributor se=
tup I had on the car, maybe you can measure the thickness of the shim betwe=
en the distributor and the distributor pedestal (I think it was about 5/16"=
thick). That will save me from doing the calculation. I have a=
wiring diagram for this electronic distributor setup if anyone is interest=
ed. The Datsun distributor was about $65 on Ebay.</div><div dir=3D"lt=
r" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false">T=
hanks for any help you can give me with this.</div><div dir=3D"ltr" data-se=
tdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false">Jack Wheele=
r<br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr=
" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><b=
r></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" d=
ata-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br><=
/div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data=
-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></di=
v><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-se=
tdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><=
div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdi=
r=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div=
dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=
=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div =
dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D=
"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=
=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"fa=
lse"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D=
"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false=
"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"lt=
r" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><=
br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" =
data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br>=
</div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" dat=
a-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></d=
iv><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-s=
etdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div>=
<div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setd=
ir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><di=
v dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=
=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div =
dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D=
"false"><br></div><div dir=3D"ltr" data-setdir=3D"false"><br></div><div dir=
=3D"ltr" data-setdir=3D"false"><br></div><div dir=3D"ltr" data-setdir=3D"fa=
lse">.<br></div></div></body></html>
------=_Part_1579682_1585996120.1687101272506--
--===============1582122926009049506==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://autox.team.net/archive http://www.team.net/pipermail/fot
--===============1582122926009049506==--
|