Les,
By the installed height of the springs, I meant from upper spring perch
to lower spring perch. Are the springs compressed the same amount?
The front suspension a-arms - The a-arms go from the kingpin, spring
perch to the frame. The metastatic bushings at the frame can bind and
the a-arms won't move through their full range of travel. As you have
the springs out, you can see how easy each side moves up and down. Do
the lower arms move freely? Do the upper a-arms (shocks) move without
any binding?
Normally when assembling the front suspension folks don't tighten up the
castellated nuts (and install the cotter pins) until the car is sitting
on the ground with the engine in it.
Cheers,
Bob Haskell
AHCA 3000 MkI registrar
http://www.ciahc.org/registry_3000mk1.php
On 01/14/2017 09:44 AM, Les Mathieson wrote:
> Hi Bob
>
> Thanks
>
> I won?t be able to get to the car until later this coming week.
>
> I assume you mean the height of the springs as mounted in the car say
> from the ground? I will check.
>
> the difference in one wheel arch to the other is about 50mm, measuring
> from ground or the wheel.
>
> When I measure the height of say the top of the headlights to ground I
> get a similar discrepancy.
>
> From my memory the height of the chassis rails etc. seem to be ok. The
> cross member seems to be also ok & horizontal.
>
> Were the front A arm inboard mounting bolts tightened with the car
> sitting flat on the ground (normal ride height)? Where actually do you mean?
>
> How's the back of the car? It's not pitching the right front nose
> downward, right? The back of the car seems ok.
>
> Cheers
>
> Les
>
> -----Original Message-----
> From: Bob Haskell [mailto:rchaskell at earthlink.net]
> Sent: Sunday, January 15, 2017 1:21 AM
> To: John Sims; Healey List; mathlynn at bigpond.net.au
> Subject: Re: [Healeys] FW: BN4 - 100/6 front suspension
>
> Jon & Les,
>
> Installed height of the springs the same?
>
> Were the front A arm inboard mounting bolts tightened with the car
> sitting flat on the ground (normal ride height)?
>
> How's the back of the car? It's not pitching the right front nose
> downward, right?
>
> Cheers,
>
> Bob Haskell
>
> AHCA 3000 MkI registrar
>
> http://www.ciahc.org/registry_3000mk1.php
>
> On 01/14/2017 07:15 AM, John Sims wrote:
>
> > Can one of you help this person with his problem? Thanks
>
> >
>
> > John Sims
>
> >
>
> > *From:*Les Mathieson [mailto:mathlynn at bigpond.net.au]
>
> > *Sent:* Friday, January 13, 2017 6:50 PM
>
>
> > *Subject:* BN4 - 100/6 front suspension
>
> >
>
> > Hi John,
>
> >
>
> > My name is Les Mathieson, from Paynesville in Australia,
>
> >
>
> > I own an 100/6, pictured.
>
> >
>
> > You have a great site, just wondering if you could give me some advice.
>
> >
>
> > My car has a ride height in the front, basically the right hand side
>
> > of the body is about 50mm or 2 inches lower than the right hand side.
>
> >
>
> > We have checked most things and nothing was apparent.
>
> >
>
> > Therefore we suspected one of the Coil springs in the front are the
>
> > issue. I have them out & we sent them to a pretty reputable spring
>
> > maker for testing etc before we bought a new set.
>
> >
>
> > Unfortunately the tests showed they were both ok?
>
> >
>
> > We are waiting for them to be returned to re-assemble & look for other
>
> > causes of the issue.
>
> >
>
> > Do you have any clues, insights or comments that might assist?
>
> >
>
> > Thanks
>
> >
>
> > Les
>
> >
>
> > Les Mathieson
>
> >
>
> > 4 Araluen Court
>
> >
>
> > (PO Box 142)
>
> >
>
> > Paynesville
>
> >
>
> > VIC 3880
>
> >
>
> > 0418106725
>
> >
>
> >
>
> >
>
> > _______________________________________________
>
> > Support Team.Net http://www.team.net/donate.html Suggested annual
>
> > donation $12.75
>
> > Archive: http://www.team.net/archive
>
> > Forums: http://www.team.net/forums
>
> >
>
>
> > http://autox.team.net/mailman/listinfo/healeys
>
> >
>
> > Unsubscribe/Manage:
>
> > http://autox.team.net/mailman/options/healeys/rchaskell at earthlink.net
>
> >
>
|