--===============2213645310169712032==
boundary="----=_Part_2005001_1539692999.1467058396580"
------=_Part_2005001_1539692999.1467058396580
Content-Transfer-Encoding: quoted-printable
Hello All,I disassembled my TR4 race car engine this past week. Last time =
I rebuilt it was 1987. Last time I raced it was 1988. Probably had five or =
six race weekends=C2=A0on the engine but its been sitting for almost twenty=
years!=C2=A0It is amazing everything looks very good. Rod and Main bearing=
s show minimal ware and the same with the pistons and liners. G3 cam and fo=
llowers including head and valves all look good. Cam bearings look question=
able...
So I plan on installing new cam bearings, Rods & Mains. Any suggestions as =
to what brand and where to buy them?I will deck the block. Any suggestions =
as to other machining I should do to the block?=20
The crank looks fine but I haven't measured it yet. What clearances should =
I run?I do plan on balancing and polishing it.
Thanks for any input.
Steve and son MatthewFlorida TR4
------=_Part_2005001_1539692999.1467058396580
Content-Transfer-Encoding: quoted-printable
<html><head></head><body><div style=3D"color:#000; background-color:#fff; f=
ont-family:HelveticaNeue, Helvetica Neue, Helvetica, Arial, Lucida Grande, =
sans-serif;font-size:12px"><div id=3D"yui_3_16_0_ym19_1_1467057166423_3010"=
> Hello All,</div><div id=3D"yui_3_16_0_ym19_1_1467057166423_3009" dir=3D"=
ltr">I disassembled my TR4 race car engine this past week. Last time I rebu=
ilt it was 1987. Last time I raced it was 1988. Probably had five or six ra=
ce weekends on the engine but its been sitting for almost twenty years=
! It is amazing everything looks very good. Rod and Main bearings show=
minimal ware and the same with the pistons and liners. G3 cam and follower=
s including head and valves all look good. Cam bearings look questionable..=
.</div><div id=3D"yui_3_16_0_ym19_1_1467057166423_3094" dir=3D"ltr"><br></d=
iv><div id=3D"yui_3_16_0_ym19_1_1467057166423_3095" dir=3D"ltr">So I plan o=
n installing new cam bearings, Rods & Mains. Any suggestions as to what=
brand and where to buy them?</div><div dir=3D"ltr">I will deck the block. =
Any suggestions as to other machining I should do to the block? </div><div =
dir=3D"ltr"><br></div><div dir=3D"ltr">The crank looks fine but I haven't m=
easured it yet. What clearances should I run?</div><div dir=3D"ltr">I do pl=
an on balancing and polishing it.</div><div dir=3D"ltr"><br></div><div dir=
=3D"ltr">Thanks for any input.</div><div dir=3D"ltr"><br></div><div dir=3D"=
ltr">Steve and son Matthew</div><div dir=3D"ltr">Florida TR4</div><div id=
=3D"yui_3_16_0_ym19_1_1467057166423_3092" dir=3D"ltr"><br></div><div id=3D"=
yui_3_16_0_ym19_1_1467057166423_3093" dir=3D"ltr"><br></div><div id=3D"yui_=
3_16_0_ym19_1_1467057166423_3080" dir=3D"ltr"><br></div><div id=3D"yui_3_16=
_0_ym19_1_1467057166423_3081" dir=3D"ltr"><br></div></div></body></html>
------=_Part_2005001_1539692999.1467058396580--
--===============2213645310169712032==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
--===============2213645310169712032==--
|