Great post Greg. These are the posts I like to see. Very thorough and very
helpful! I learned something new today!
Ty
TR4 #413
Sent from my iPad
(Please excuse any errors or typos)
On Jan 29, 2013, at 1:15 AM, "Greg Solow" <gregmogdoc@surfnetusa.com> wrote:
> ----- Original Message ----- From: <gregmogdoc@surfnetusa.com>
> To: <tr4@wi.rr.com>; <fot@autox.net>
> Cc: <Gregmogdoc@surfnetusa.com>
> Sent: Monday, January 28, 2013 11:34 PMgh
> Subject: RE: Re: [Fot] Flex hone life span & lube
>
>
> flexhone has specific recommendations for the grit to
> use based on the material your top compression rings
> are faced with. Cast irom ring call for the coursest
> finish, chromed rings use a finer grit and moly
> filled or plasma sprayed rings call for the finest
> grit. I believe the exact grits are noted in their
> catalogue. We have always honed the cylinders with a 1/2" drive
> drill with plenty of "stoddard solvent" that is the
> regular petroleum based solvent used to clean parts
> in a solvent tank (not a "hot tank" or "carb dip").
> We then wipe the cylinder down with auto trans fluid
> and a white towel and paper towels until NO MORE GREY
> color comes comes off of the cylinder walls. The
> auto trans fluid is very good at lifting grit and
> debris out of the pores of the metal of the cylinder
> & at the same time prevents the walls from rusting.
> We like it much better than "washing with soap and
> water and a brush" which is the old stand-by taught
> in auto shop class and in vintage text books.
>
> Greg Solow
> The Engine Room
> Sports Car Specialists
> Santa Cruz, CA 95060
> 831 429-1800
>
>
>
> ------- Original Message -------
> From : Steve Yott[mailto:tr4@wi.rr.com]
> Sent : 1/28/2013 10:14:03 AM
> To : toodamnfunky@comcast.net; fot@autox.team.net
> Cc : Subject : RE: Re: [Fot] Flex hone life span & lube
>
> I would recommend taking a look at the following
> site... No personal
> involvement here it's just that I have read most of
> their info which is
> good. Flex Hones come in various sizes in the
> cylinder bore range by 1/4
> and 1/2 inch increments. You do not need an exact
> size but should use the
> next oversize if you are honing a bore that is the
> same as a size offered.
> They recommend Flex Hone oil but I use a 50/50 mix of
> mineral spirits and
> automatic transmission fluid. I always use two grits
> and normally start
> with a 120 and then finish with a 240.
>
> http://www.enginehones.com/
> Steve Yott
> -----Original Message-----
>
>
>
>
> Behalf Of toodamnfunky@comcast.net
>
>
> FoT
> I'm just inquiring about flex hones. I have one I've
> used once and on the
> second time round
> It doesn't seem to cut the way it did last time.
> Since they are made to a
> specific bore size
> their service life has to be limited but how limited ?
> Also, what is everybody favorite cutting solution to
> use while running a
> hone.
> Thanks as always,
> jim g
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
> Donate: http://www.team.net/donate.html Archive:
_______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
> Donate: http://www.team.net/donate.html Archive:
http://autox.team.net/mailman/options/fot/gregmogdoc@surfnetusa.com
> _______________________________________________
> fot@autox.team.net
>
> http://www.fot-racing.com
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe/Manage:
http://autox.team.net/mailman/options/fot/tylerpthompson@yahoo.com
_______________________________________________
fot@autox.team.net
http://www.fot-racing.com
Archive: http://www.team.net/archive
|