fot
[Top] [All Lists]

Re: [Fot] Finding TDC

To: David Talbott <dtalbott@archrepro.com>
Subject: Re: [Fot] Finding TDC
From: Bill Babcock <Billb@bnj.com>
Date: Tue, 10 Jun 2008 08:32:28 -0700
One of the reasons I always liked two strokes--suck and squeeze  
happens at the same time, the challenging part is that so do bang and  
blow.
On Jun 9, 2008, at 4:25 PM, David Talbott wrote:

> Jesus, Mark, you need to be more careful when you talk about this  
> suckin',
> squeezin', bangin', and blowin' stuff in a semi-public forum.  You  
> take that
> to the extreme, like a recent V10 F1 engine at close to 20,000  
> RPM's, and
> that's enough of the aforementioned activity in a single minute to  
> get a
> feller all worked up.  All you need now is for Babcock to chime in  
> on the
> two stroke equivalents of this and some of our senior correspondents  
> like
> ol' Damndinger could literally pop a danged gasket.
>
> DT
>
> ----- Original Message -----
> From: "Mark J Bradakis" <mark@bradakis.com>
> To: <fot@autox.team.net>
> Sent: Sunday, June 08, 2008 8:25 PM
> Subject: Re: [Fot] Finding TDC
>
>
>>> 2)       Rotate the engine 360 degrees, this is approximately TDC.
>>>
>>>
>> What, exactly, is the purpose of this step?  Rotating the crank 360
>> degrees
>> will put it exactly where it was.  If you want to check the  
>> distributor
>> position
>> to see if the rotor is about where it should be when #1 is at TDC  
>> ready to
>> fire just turn the crank until the valves for #4 are "on the rock"
>> instead of
>> the number 1 cylinder.
>>
>> In the four cycle suck, squeeze, bang and blow process TDC in a  
>> cylinder
>> occurs between squeeze and bang, and again between blow and suck.   
>> The
>> blow /suck TDC is when the valves for that cylinder are on the  
>> rock, given
>> a basic, symmetrical cam grind.
>>
>> The length of the bolt or nut whatever you firmly attach doesn't  
>> matter,
>> though the shorter the better to prevent deflection.  Wherever the  
>> two
>> marks for the clockwise and counterclockwise rotations end up, TDC is
>> halfway between the two.
>>
>> mjb.
>>
>> PS:  The wedding in Irvine wasn't too bad, back in Salt Lake, lots of
>> email, Team.Net admin stuff, etc. to catch up on.
>> _______________________________________________
>> http://www.team.net/donate.html
>>
>> Fot mailing list
>> Fot@autox.team.net
>> http://autox.team.net/mailman/listinfo/fot
>>
>> You are subscribed as dtalbott@archreproduction.com
> _______________________________________________
> http://www.team.net/donate.html
>
> Fot mailing list
> Fot@autox.team.net
> http://autox.team.net/mailman/listinfo/fot
>
> You are subscribed as billb@bnj.com

Bill Babcock
Babcock & Jenkins
Billb@bnj.com
503.936.7660
www.bnj.com
_______________________________________________
http://www.team.net/donate.html

Fot mailing list
Fot@autox.team.net
http://autox.team.net/mailman/listinfo/fot


<Prev in Thread] Current Thread [Next in Thread>