Enter the part number into the white box at the bottom of the scroll bar in
our web-site then hit search.
65 - 67, 67 1/2 , 68-70 Door Panels with original looking pleated pockets.
$120.00 per pair. Part #1336
New replica trunk weatherstrip, like the ones that came originally with the
cars, for authentic restorations. Made of Santoprene. Won't rot or crack like
the original. Coming Soon. $40.00 Part# 1352
New replica 65 - 67 1/2 Windshield weatherstrip made of Santoprene. Won't rot
like original. Coming soon. $55.00 Part# 1344
67 1/2, 68 - 70 304 Laser cut stainless steel, machined formed brake master
cylinder brake brace. $10.00 Part# 1342
65 - 671/2 4 speed Shift plate label.12 mil photo etched aluminum with high
strength 3M backing for good adhesion. Same quality as the correctly made ID
plates we sell. List price $38.00 each. On sale for $14.00 Photo available
through email.
67 1/2 5 speed shift plate label. Same as above. List price $38.00 On sale for
$14.00
65 - 67 powdercoated Battery frame hold down. Never offered before. $46.00
Part #1347
67 1/2 - 70 powder coated Replica Battery Frame and tray assembly. Offered 3
ways. (1)Battery frame and Nissan tray w/drain hose use your old rods . Regular
list $63.00 On sale for $36.00. (2) Frame and tray with correctly bent hold
down rods, washers and wing nuts $46.00. (3) Frame and tray with original
Nissan rods washers and stainless steel wing nuts.$56.00. Note: Be sure to
click each photo in the web site to see the correct size of the frames
listed.Part # 1346
SR311 RH drive Solex ID plate $25.00 Part #1348
65 - 70 Datsun Hood Emblem set in METAL. $48.00 Soon to be back in stock. Part
#1340
Short run reproduction 65 - 67 Early Datsun1600 emblems. Intro price. $59.00
each. These are not over buffed sand castings or lost wax brass pieces, with
pins shrunk and too narrow from the casting process that won't fit in the holes
in the fenders, that have been floating around over the past few years. These
beauties were made in a two part mold with the pins diecast in the correct
postion. Virtually indistinguishable from the originals with similiar chrome.
Part#1337
High Strength Energy Suspension Urethane Reproduction Engine Mounts. Looks
factory stock when installed. These mounts are not only bonded like the
original but have twin welded studs on each plate, opposed at 180 degrees to
one another, imbedded in the urethane for added strength. These will not peel
apart or sag like the originals and will out live the functional life of the
Nissan counterparts and will probably last forever. Two styles available.
Regular replacement with slightly higher durometer than original and
competition version for racing with even higher durometer.
11223-32201R Regular Replacement - Black or in Datsun Blue/Green color
urethane $ 92.00 Pair
11223-32201C Competition - Gray urethane $ 92.00 Pair Part#1338
Don't forget to pair these with our urethane tranny mounts.We also have a
plentiful supply of Nissan mounts on hand.
Urethane Lower Control Arm Competition Bump stops and Upper Control Arm Bump
stops. These laser cut and steel die parts have been carefully tooled and
engineered replicating the original O.E.M parts.Same durometer as originals.
These parts are tooled not splashed. 2 - upper / 2 - lower. Set of 4 pieces
$70.00
Lower Control arm Competition Bump stops purchased out of kit $40.00 per pair.
Upper Contol arm Bump stops purchased out of kit $40.00 per pair. Part# 1339
www.datsunparts.com (818) 363-2015. ALL LISTED PARTS ARE NEW DATSUN ROADSTER
PARTS.
Tired of spam? Yahoo! Mail has the best spam protection around
---------------------------------
Yahoo! Mail
Stay connected, organized, and protected. Take the tour
|