Andrew,
I have to disagree. I have installed a number of Roadster tops (all low
windshield except for one) and they were easy. Centering the top is
critical, but it is not difficult. Stretching the top is not bad -
especially with the low windshield cars as there are adjustors to help. No
special tools needed to install the lift the dot or twisty connectors in the
top - just an Exacto knife and a little patience. There is NO WAY it takes
6 hours to do unless you stop for a 4 hour beer break in the middle.
Sid
>From: "Andrew Murphy" <solex67@hotmail.com>
>Reply-To: "Andrew Murphy" <solex67@hotmail.com>
>To: giel@earthlink.net, datsun-roadsters@autox.team.net
>Subject: Re: A few Questions about tops
>Date: Mon, 07 Jan 2002 09:32:13 -0800
>
>Bob,
>
>I have watched some of the processes necessary to install a soft top onto a
>Datsun Roadster. What is so time consuming is the fact that the top fabric
>and the top frame are not intially "joined". What takes the time is that
>holes must be punched with a very specific tool to line up the grommets
>with
>the "posties and twisties". Also, there is quite a lot or work to join the
>top fabric correctly to the front bow. If you are off by just a little the
>top will be lopsided. You also have to do quite a lot of pulling stretching
>to make sure the fabric is taught when the top frame is extended.
>
>When I had mine done at the upholsterer, it took a few hours. I have heard
>of people doing it themselves, but I don't think I would have the patience
>and where withall to do it myself.
>
>My .02,
>
>Andrew Murphy
>SoCalROC
>
>
>From: Robert Giel <giel@earthlink.net>
>Reply-To: Robert Giel <giel@earthlink.net>
>To: datsun-roadsters <datsun-roadsters@autox.team.net>
>Subject: A few Questions about tops
>Date: Mon, 07 Jan 2002 09:11:20 -0800
>
>When it comes to tops, (and too many other topics to
>mention) I am really in the dark. My 66 SPL311 1600 has
>no top of any kind, (hard, soft or tonneau) and comments on
>this list arouse my already insatiable curiosity. I have
>two different sets of soft top frames and hope that one of
>them is actually for this car, but I am not sure, never
>having seen one before. While it is more important to
>actually get the car running safely, and on the road, having
>some sort of top is in the back of my mind as another
>important, enjoyable, and related simultaneous project.
>
>I plan to make my own hard top (fiberglass and/or carbon
>reinforced plastic construction much as used to fabricate
>boats, customized vehicle and marine parts), and a tonneau
>cover (much as one makes sails and awnings.)
>
>First question: Is there any site or other source I can get
>some measured drawings, photographs, and/or specific
>dimensions of the original hard top for this car (I believe
>this is called the low windshield design)?
>
>While we are at it, how about patterns for the soft top and
>the tonneau cover? If I can get a pattern and/or worn out
>cover as a pattern/model, and then get access to an
>industrial-strength sewing machine this should be another
>fun project.
>
>My greatest curiosity regarding roadster tops has to do with
>the soft top problems mentioned on this list.
>
>Having owned a few (non-Datsun) roadsters in the past, I am
>confused as to why it is so hard and expensive to install a
>replacement soft top on the Datsuns. For my other cars, the
>frame and a front hold-down bar simply slipped into sleeves
>sewn into the fabric and it took about ten minutes on a
>really bad day to completely install or remove and store
>away! In fact, on one of my cars the soft top material was
>not stored on the frame when removed, so this slip it on and
>off process was a daily routine for me depending on the
>weather. I can remember "rushing" to do the job when caught
>in a "surprise" shower. It was not much harder than
>stretching the tonneau cover to get those metal grommets
>over the snaps and twist fasteners.
>
>Many messages on this list have mentioned hours of labor and
>hundreds of dollars just to "install" a soft top!? What is
>the story here? It is obvous that this group has some of
>the smartest folks around, so I have to ask, What the heck
>is everybody talking about?! Is the top/frame design
>actually that bad and if so, why hasnt somebody modified
>the design to get rid of an exorbitant maintenance
>nightmare, where no difficulty should exist at all? Is the
>soft top sewn onto the frame or something equally
>ridiculous? What could possibly take hours of specialized
>labor skills to install? Is there a site that describes the
>soft top and explains what must be a very arduous process?
>
>TIA,
>
>Bob Giel
>66 SPL311-05249
>Los Angeles, Calif.
>
>/// datsun-roadsters@autox.team.net mailing list
>/// Send admin requests to majordomo@autox.team.net or go to
>/// http://www.team.net/cgi-bin/majorcool
>/// Send list postings to datsun-roadsters@autox.team.net
>
>
>
>_________________________________________________________________
>
>/// datsun-roadsters@autox.team.net mailing list
>/// Send admin requests to majordomo@autox.team.net or go to
>/// http://www.team.net/cgi-bin/majorcool
>/// Send list postings to datsun-roadsters@autox.team.net
>
_________________________________________________________________
/// datsun-roadsters@autox.team.net mailing list
|