buick-rover-v8
[Top] [All Lists]

Re: CAM/INLET/CARB RECOMENDATIONS

To: "John Bartholomew" <jdb70@minerva.amdahl.com>,
Subject: Re: CAM/INLET/CARB RECOMENDATIONS
From: "Lode" <lode@glo.be>
Date: Wed, 19 May 1999 09:13:22 +0200
Instead of boring the block, why don't you put in some 3.9 sleeves and
pistons?
They shouldn't be that expensive. I would also advice Vitesse valves (bigger
and cheap)
Go for a Holley carb and an Offenhauser intake manifold. Selecting a cam
depends
on what car you gonna put this engine in. But I wouldn't go "higher" then a
fast road
cam. Don't forget to dump the standard distribution chain and gears. Throw
in some
Cloyes (or alike) gears, with a steel chain.
With above mods you can expect between 220 and 250 bhp and loads of torque.

Have fun

Lode



> Hey there listers,
>                  I have finally got my ROVER engine stripped and the block
> and crank are at the shop being renovated!
>
> Having stipped this sucker down, I know I need to replace the cam and
> lifters and the block needs to be bored as one piston #4 was rusted in
> pretty good, took a 2x2 of oak and a 7lb sledge to move it out.
> The remainder were in pretty good shape. Seems a couple of bores had taken
> in some antifreeze and it has sat that way for ???. The guy at the local
> shop tells me this block is in great shape, just looking at the water
ways.
> They are all clean as a whistle and the water pump is probably still
> usable.  I am gonna replace it anyway.
> There are a couple of lobes of the cam that are well gone and some of the
> lifters are really cupped, so it's new cam time.  This is where I could do
> with so advice from you knowledgable V8 users.  This is my first V8 I have
> ever been inside, I find it no so different from the 4 bangers I have
> worked on, just a few more pistons and a longer cam. So here is my
> question.  What would be a good cam to get, I want to get something that
is
> streetable and will give the motor a little kick. Say one level above the
> standard cam. I will need to replace the pistons and an gonna go with the
> 9.? compression, which I think was standard on this motor.  It's the Rover
> 3500 and had, has, the SU carburettors. Which leads me to my next point.
> What manifold and carb set up should I go with?  Should I select my cam to
> match my carbs? Most of the SU carbs are there, but they are missing the
> float bowls and fittings. Would you listers recommend staying with the
SU's
> or go with some other set up.  I think I am going to have to replace the
> inlet manifold as it looks like the current set up will be too high for
the
> "B" to be able to clear the hood. So I can justify replacing the manifold
> and the carbs. Have you folks any info on what works so I can go shopping.
> I am not looking for over kill and I don't want to be under the hood every
> trip tweeking. I would like something that will stay setup that I won't
> have to keep adjusting. I have no experiance with anything but SU's
> however, I am willing to learn!
> Any suggestions would be welcome...TIA -John.
> ---------------------------------
>      E-mail jdb70@minerva.amdahl.com
>   John Bartholomew Amdahl San Jose CA.
>   ** 408-746-6361 07:00-16:00 PST.  **
>     **  USUAL DISCLAIMERS APPLY  **
> Various MGB & GT's (6) '69 to 79; 86 XJ-S COUPE
>


<Prev in Thread] Current Thread [Next in Thread>