You can also carefully enlarge the bolt holes in the gasket with a home made
punch.
> The coefficent of expansion of copper is 17, steel is 11 (higher means more
> expansion). So cooling the copper will "Shrink" it. Good idea to put the
> gasket in the freezer. Here is the wikipedia website link if you wish to
> learn more on thermal expansion.
>
> http://en.wikipedia.org/wiki/Coefficient_of_thermal_expansion
>
> Kevin
>
> -----Original Message-----
>> From: Ron Christensen <ron.christensen@wsapr.com>
>> Sent: Sep 28, 2007 10:32 AM
>> To: 'Iain Hueton' <ihueton@yahoo.com>, 'Jeremiah Curry'
>> <jeremiah@curryclan.net>, owner-triumphs@Autox.Team.Net, bmcu@autox.team.net
>> Subject: Re: [Bmcu] 57 TR3 head studs not lined up?
>>
>> The gasket, being copper, is resistant to shrinkage. Only heating the block
>> will work.
>>
>> -----Original Message-----
>> From: Iain Hueton [mailto:ihueton@yahoo.com]
>> Sent: Friday, September 28, 2007 10:14 AM
>> To: Ron Christensen; Jeremiah Curry; owner-triumphs@Autox.Team.Net;
>> bmcu@autox.team.net
>> Subject: Re: [Bmcu] 57 TR3 head studs not lined up?
>>
>> could you throw the gasket in the freezer to shrink it down, slide over the
>> bolts, and then let it warm up in place?
>> Iain
>>
>> Iain Hueton
>> www.toriandesigns.com
>> 1804 Ross Drive
>> Ogden, UT 84403
>> H 801-340-0049
>> email ihueton@yahoo.com
>>
>>
>> ----- Original Message ----
>> From: Ron Christensen <ron.christensen@wsapr.com>
>> To: Jeremiah Curry <jeremiah@curryclan.net>; owner-triumphs@Autox.Team.Net;
>> bmcu@autox.team.net
>> Sent: Friday, September 28, 2007 10:12:08 AM
>> Subject: Re: [Bmcu] 57 TR3 head studs not lined up?
>>
>>
>> It is a common problem with all British cars . . . . block shrinkage. Take
>> the engine out and warm it to 1000 degrees and the gasket should slide right
>> on.
>>
>> -----Original Message-----
>> From: bmcu-bounces@autox.team.net [mailto:bmcu-bounces@autox.team.net] On
>> Behalf Of Jeremiah Curry
>> Sent: Thursday, September 27, 2007 9:20 PM
>> To: owner-triumphs@Autox.Team.Net; bmcu@autox.team.net
>> Subject: [Bmcu] 57 TR3 head studs not lined up?
>>
>> Howdy all,
>>
>> I am getting ready to put the head on my TR3 for the first time since I got
>> it. A few weeks ago I went to put the head gasket on and found that the
>> holes in the gasket didn't exactly line up with the holes studs. I figured
>> the studs must be bent, so I stopped and ordered new ones. However after
>> putting the new studs in I find the same problem, maybe a little less
>> severe, but the same problem. I don't know if I can even get the gasket on
>> without tearing it to pieces.
>>
>> Has anyone else seen this before or have any insight?
>>
>> thanks,
>> Jeremiah
>>
>> [demime 1.01d removed an attachment of type application/ms-tnef which had a
>> name of winmail.dat] _______________________________________________
>> Bmcu mailing list
>> Bmcu@autox.team.net
>> http://autox.team.net/mailman/listinfo/bmcu
>> _______________________________________________
>> Bmcu mailing list
>> Bmcu@autox.team.net
>> http://autox.team.net/mailman/listinfo/bmcu
>> _______________________________________________
>> Bmcu mailing list
>> Bmcu@autox.team.net
>> http://autox.team.net/mailman/listinfo/bmcu
> _______________________________________________
> Bmcu mailing list
> Bmcu@autox.team.net
> http://autox.team.net/mailman/listinfo/bmcu
_______________________________________________
Bmcu mailing list
Bmcu@autox.team.net
http://autox.team.net/mailman/listinfo/bmcu
|