--===============1663060807711239169==
--0000000000007070ef05d8ae80c9
I always remove the outer axles to grease the outer u-joint. I find it
usually pays to take the brake drum off to check stuff so it's no big deal
to pull the outer axles. Plus you get to make sure the studs for the hub
attachment are not stripped. You can also use the opportunity to clean up
the brake dust.
C ya
Bob Lang
On Wed, Feb 23, 2022, 1:42 AM im sloane <im_sloane@hotmail.com> wrote:
> I've always heard it's impossible to grease those 2 u-joints, unless you
> have a hole cut in your wishbones at just the right place. I suppose it's
> obvious that you'd want to just replace them during a hub rebuild.
>
> Sloane
> 69-Six
> 72-Spit
> ------------------------------
> *From:* 6pack <6pack-bounces@autox.team.net> on behalf of Yahoo <
> brucesimms2003@yahoo.ca>
> *Sent:* Tuesday, February 22, 2022 8:12 PM
> *To:* 6pack@autox.team.net <6pack@autox.team.net>
> *Subject:* [6pack] question for 6packers if too quiet
>
> I've always had trouble greasing the ujoint that joins the rear hub and
> the drive shaft. Access is quite limited and I cant see the grease
> nipple. Advice or tricks on accomplishing this? Easy to do if hub is
> off the car.
> Thank you, Bruce 73 tr6
>
> Sent from Yahoo Mail on Android
> <https://go.onelink.me/107872968?pid=InProduct&c=Global_Internal_YGrowth_AndroidEmailSig__AndroidUsers&af_wl=ym&af_sub1=Internal&af_sub2=Global_YGrowth&af_sub3=EmailSignature>
> _______________________________________________
> Support Team.Net http://www.team.net/donate.html
> Suggested annual donation $12.96
> Archive: http://www.team.net/archive
>
>
> 6pack@autox.team.net
> http://autox.team.net/mailman/listinfo/6pack
>
> Unsubscribe/Manage:
> http://autox.team.net/mailman/options/6pack/robert.lang.tr6@gmail.com
>
>
--0000000000007070ef05d8ae80c9
Content-Transfer-Encoding: quoted-printable
<div dir=3D"auto">I always remove the outer axles to grease the outer u-joi=
nt. I find it usually pays to take the brake drum off to check stuff so it&=
#39;s no big deal to pull the outer axles.=C2=A0 Plus you get to make sure =
the studs for the hub attachment are not stripped. You can also use the opp=
ortunity to clean up the brake dust.=C2=A0<div dir=3D"auto"><br></div><div =
dir=3D"auto">C ya</div><div dir=3D"auto">Bob Lang=C2=A0</div></div><br><div=
class=3D"gmail_quote"><div dir=3D"ltr" class=3D"gmail_attr">On Wed, Feb 23=
, 2022, 1:42 AM im sloane <<a href=3D"mailto:im_sloane@hotmail.com";>im_s=
loane@hotmail.com</a>> wrote:<br></div><blockquote class=3D"gmail_quote"=
style=3D"margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div dir=3D"ltr">
<div style=3D"font-family:Calibri,Helvetica,sans-serif;font-size:12pt;color=
:rgb(0,0,0)">
I've always heard it's impossible to grease those 2 u-joints, unles=
s you have a hole cut in your wishbones at just the right place. I suppose =
it's obvious that you'd want to just replace them during a hub rebu=
ild.=C2=A0</div>
<div style=3D"font-family:Calibri,Helvetica,sans-serif;font-size:12pt;color=
:rgb(0,0,0)">
<br>
</div>
<div style=3D"font-family:Calibri,Helvetica,sans-serif;font-size:12pt;color=
:rgb(0,0,0)">
Sloane=C2=A0</div>
<div style=3D"font-family:Calibri,Helvetica,sans-serif;font-size:12pt;color=
:rgb(0,0,0)">
69-Six</div>
<div style=3D"font-family:Calibri,Helvetica,sans-serif;font-size:12pt;color=
:rgb(0,0,0)">
72-Spit</div>
<div id=3D"m_-6610095919130547347appendonsend"></div>
<hr style=3D"display:inline-block;width:98%">
<div id=3D"m_-6610095919130547347divRplyFwdMsg" dir=3D"ltr"><font face=3D"C=
alibri, sans-serif" style=3D"font-size:11pt" color=3D"#000000"><b>From:</b>=
6pack <<a href=3D"mailto:6pack-bounces@autox.team.net"; target=3D"_blank=
" rel=3D"noreferrer">6pack-bounces@autox.team.net</a>> on behalf of Yaho=
o <<a href=3D"mailto:brucesimms2003@yahoo.ca"; target=3D"_blank" rel=3D"n=
oreferrer">brucesimms2003@yahoo.ca</a>><br>
<b>Sent:</b> Tuesday, February 22, 2022 8:12 PM<br>
<b>To:</b> <a href=3D"mailto:6pack@autox.team.net"; target=3D"_blank" rel=3D=
"noreferrer">6pack@autox.team.net</a> <<a href=3D"mailto:6pack@autox.tea=
m.net" target=3D"_blank" rel=3D"noreferrer">6pack@autox.team.net</a>><br=
>
<b>Subject:</b> [6pack] question for 6packers if too quiet</font>
<div>=C2=A0</div>
</div>
<div>I've always had trouble greasing the ujoint that joins the rear hu=
b and the drive shaft. Access is quite limited and I cant see the grease=C2=
=A0 nipple.=C2=A0 =C2=A0 =C2=A0Advice or tricks=C2=A0 on accomplishing this=
?=C2=A0 =C2=A0Easy to do if hub is off the car.
<div>Thank you,=C2=A0 =C2=A0 Bruce 73 tr6<br>
<br>
<div id=3D"m_-6610095919130547347x_ymail_android_signature"><a id=3D"m_-661=
0095919130547347x_ymail_android_signature_link" href=3D"https://go.onelink.=
me/107872968?pid=3DInProduct&c=3DGlobal_Internal_YGrowth_AndroidEmailSi=
g__AndroidUsers&af_wl=3Dym&af_sub1=3DInternal&af_sub2=3DGlobal_=
YGrowth&af_sub3=3DEmailSignature" target=3D"_blank" rel=3D"noreferrer">=
Sent
from Yahoo Mail on Android</a></div>
</div>
</div>
</div>
_______________________________________________<br>
rer noreferrer" target=3D"_blank">http://www.team.net/donate.html</a><br>
Archive: <a href=3D"http://www.team.net/archive"; rel=3D"noreferrer noreferr=
er" target=3D"_blank">http://www.team.net/archive</a><br>
<br>
<br>
<a href=3D"mailto:6pack@autox.team.net"; target=3D"_blank" rel=3D"noreferrer=
">6pack@autox.team.net</a><br>
<a href=3D"http://autox.team.net/mailman/listinfo/6pack"; rel=3D"noreferrer =
noreferrer" target=3D"_blank">http://autox.team.net/mailman/listinfo/6pack<=
/a><br>
<br>
robert.lang.tr6@gmail.com" rel=3D"noreferrer noreferrer" target=3D"_blank">=
http://autox.team.net/mailman/options/6pack/robert.lang.tr6@gmail.com</a><b=
r>
<br>
</blockquote></div>
--0000000000007070ef05d8ae80c9--
--===============1663060807711239169==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
_______________________________________________
Archive: http://www.team.net/archive
6pack@autox.team.net
http://autox.team.net/mailman/listinfo/6pack
--===============1663060807711239169==--
|