You may have been able to drill&tap the holes without removing the rods,
depending on how much lead was on the tap.
Berry
-----Original Message-----
From: John North <johncnorth@gmail.com>
To: Triumph 6 Pack <6pack@autox.team.net>
Sent: Mon, Dec 16, 2013 10:53 am
Subject: Re: [6pack] Gear selector shaft detents
I was able to get the loose ball back in the shaft using a dummy shaft
about 3" long with the end cut at a 45 degree angle. I used 1/2" rod
from Home Depot. I pushed it in from the back using the real shaft
while easing the ball back into the slot with a screwdriver from the
front. This allowed me to get back to square one with all three
shafts in place and operating.
So then I extended the dummy shaft idea and made three about 5" long
and inserted them from the front as I withdrew the shafts. These
kept the detent balls in their channel. I shook out the two
interlock balls that prevent selecting more than one gear at a time as
I inserted the dummy shafts.
So now I have the top cover clear and can drill and tap...
John North
1976 TR6
On Sun, Dec 15, 2013 at 9:10 PM, Sally or Dick Taylor
<taylorturbo6@yahoo.com> wrote:
> Hi,John --- I drilled out these plugs and tapped out the holes using a
7/16"
> tap. (Don't recall the TPI) The thread depth isn't as deep as would
normally
> be the case, due to the larger hole to begin with. But there's not much
> pressure being exerted on these socket head SET SCREWS, and I recall them
> being covered. It's been years, so forgive the lack of details. The
downside
> of using the 7/16" set screws was they don't come in the short length
> necessary, and must be shortened to be flush with the top of the case. If I
> had to do this over today, I'd make new plugs rather than tap for set
> screws. Not a chance of this, however, as there's a 5 speed taking it's
> place!
>
> Dick
>
>
> On Sunday, December 15, 2013 2:51 PM, John North <johncnorth@gmail.com>
> wrote:
>
> Ok, I see that these plugs are NA at TRF, Moss and Vic Brit... I
> looked over the Mcaster Carr site, couldn't find what I need although
> they have just about everything known to man. Anybody got a lead on
> where I can get them?
>
> John North
> 1976 TR6
>
> On Sun, Dec 15, 2013 at 12:02 PM, Larry Young <cartravel@pobox.com> wrote:
>> Go to the maintenance page at vtr -
>> http://www.vtr.org/maintain-index.shtml
>> and look at the end of "Rebuilding the Triumph TR Transmission Part 2".
>> It
>> explains how to overhaul a top cover and drill one for overdrive switches.
>> For the late boxes you have to drill out the plugs. You may be able to
>> match the plugs at your local auto parts store or drill and tap them for
>> plugs like the early covers. Top covers are probably one of the most
>> neglected transmission parts.
>> Larry Young
>>
>>
>> On 12/14/2013 2:56 PM, John North wrote:
>>>
>>> I am removing the shafts to drill and tap for overdrive switches...
>>> The manual says to unscrew the screw plugs that hold the springs and
>>> balls, but my 76 does not have screwed plugs, they appear to be
>>> interference fit plugs, see this pic...
>>>
>>> http://tinyurl.com/oufsve6
>>>
>>> So there is no way that I can see to get the plugs out.
>>>
>>> I did remove one of the shafts and of course the ball fell into the
>>> shaft tube and left the spring sticking into the tube. I can get the
>>> spring and ball back into what I think is the right position with a
>>> screwdriver and seal puller, but haven't been able to get it back into
>>> the hole to allow the shaft to pass under it.
>>>
>>> So two questions, first, what's the best way to handle the other two
>>> shafts and not make the same mistake... and second, how do I get the
>>> ball back in?
>>>
>>> Any help appreciated
>>>
>>> John North
>>>
>>> ________________________________________
>>>
>>> 6pack@autox.team.net
>>>
>>> Donate: http://www.team.net/donate.html
>>> Archive: http://www.team.net/archive
>>> Forums: http://www.team.net/forums
>>> Unsubscribe:
>>> http://autox.team.net/mailman/options/6pack/cartravel@pobox.com
>
> ________________________________________
>
> 6pack@autox.team.net
>
> Donate: http://www.team.net/donate.html
> Archive: http://www.team.net/archive
> Forums: http://www.team.net/forums
> Unsubscribe:
> http://autox.team.net/mailman/options/6pack/taylorturbo6@yahoo.com
________________________________________
6pack@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/6pack/btp44@aol.com
________________________________________
6pack@autox.team.net
Archive: http://www.team.net/archive
Unsubscribe: http://autox.team.net/mailman/options/6pack/mharc@autox.team.net
|