healeys
[Top] [All Lists]

Re: [Healeys] The Story of Positive Earth (and Electrics 101)

To: "josef-eckert@t-online.de" <josef-eckert@t-online.de>, "Healey, Forum" <healeys@autox.team.net>
Subject: Re: [Healeys] The Story of Positive Earth (and Electrics 101)
From: Bob Spidell via Healeys <healeys@autox.team.net>
Date: Sun, 15 Nov 2026 06:22:12 -0800
Authentication-results: autox.team.net; header.b="DiDzTOsk"
Delivered-to: mharc@autox.team.net
Delivered-to: healeys@autox.team.net
References: <34736438-3d60-a433-ed8e-70bd64024581@charter.net> <CAB3i7L+r2dJCo_OGLTKZ=xHCJa2XKRoM7cpS9SE23k0B8+tMpQ@mail.gmail.com> <59a03803-32e7-4be1-a902-d4914bdffbb4@comcast.net> <1794727138791.187398.de6010d65392748982ca71eb5333e6a3f1314fae@spica.telekom.de>
User-agent: Mozilla Thunderbird
Xfinity-graffiti: 70204490354
Xfinity-qid: Sb7VxTSJbNN4nSb7Wxe7Dg
This is a multi-part message in MIME format.
--===============5189488682828184288==
 boundary="------------Je0imF3Uiswqt1AGno0OISDm"
Content-Language: en-US

This is a multi-part message in MIME format.
--------------Je0imF3Uiswqt1AGno0OISDm
Content-Transfer-Encoding: 8bit

Nope.

On 11/14/2026 11:18 PM, josef-eckert@t-online.de wrote:
>
> I think that´s far over the top what you do. Have you ever tried just 
> one of the two batteries?
>
> I use just one Harley Davidson motorcycle 12Volt, 35 Ah, battery which 
> is covered by the original battery body top, left and right side. Only 
> front and rear of the battery are not covered, which can´t be seen. 
> The second is just a dummi. That works fine for me and it always gets 
> the engine cranked in full speed to start it.
>
> Josef Eckert
>
> Konigswinter. Germany
>
> -----Original-Nachricht-----
>
> Betreff: Re: [Healeys] The Story of Positive Earth (and Electrics 101)
>
> Datum: 2026-11-15T04:24:13+0100
>
> Von: "Bob Spidell via Healeys" <healeys@autox.team.net>
>
> An: "healeys@autox.team.net" <healeys@autox.team.net>
>
> I got fed up with the 17H 6Vs I'd used for years; they were hard to 
> find, would barely crank my BN2's (170+psi on all 4) rebuilt starter 
> and came close to contacting the lid. So, I threw in the towel on 
> original. IIRC, these are over 450CCA so two in parallel give close to 
> 900A, with 00 cables linking them in parallel. The starter sounds 
> stronger than my BJ8's with a 500CCA AGM.
>
> https://4xspower.com/collections/d-series-batteries     (NFI).
>
>
> If my (rudimentary) knowledge is correct, inductive loads like 
> starters are almost dead shorts for a few milliseconds, until 
> impedance builds as the motor starts to rotate (hence 450 amps). 
> Besides the current draw, there will be a voltage drop, which reduces 
> cranking power. I'd be interested in a voltage reading during 
> cranking; old school load testers--the kind with carbon pile 
> resistance--use the voltage drop to determine if a battery is good 
> (and they usually test for 30 seconds or more). Of course, cold 20W/50 
> oil doesn't facilitate easy starting.
>
> One of my tractors--an early Ford--had a single 6V battery and pos. 
> gnd. and starting it was a coin toss. It would only crank, very 
> slowly, for about 20 seconds before giving up the ghost. I recently 
> converted it to 12V neg. gnd. and it snaps to life on the first or 
> second crank.
>
> Bob
>
>
> On 11/14/2026 10:52 AM, Michael Salter wrote:
>
>     Interesting that you should bring this subject up Hank. I'm always
>     on the lookout for a solution but, as yet not much has shown up.
>     The primary issue is the "stalled" current draw of the M418
>     starter motor of around 450 amps.
>     I have found a 12 volt battery which will fit into the case which
>     delivers 225 amps.
>     Tests on my BN1 with around 9.5: 1 compressions show that it can
>     draw something like 280 amps on a cold day at first attempt with
>     20/50 oil.
>     Once it has cranked over a few times this drops to under 200 amps.
>     My BN2 with its standard 7.5:1 compressions only draws around 130
>     amps from cold.
>     I'm working with a battery company at present who have a "power
>     sports" battery which would fit into the original case which
>     delivers 225 CCA so it's likely that that battery would work with
>     the BN2 but, because it is fuel injected I'm still trying to
>     figure out if that battery has sufficient reserve capacity to
>     provide the 8 amps the EFI system requires for sufficient time at
>     idle.
>     BTW, not wanting to burst your bubble but I'm fairly sure now that
>     the 17L cases suppied by Antique Battery actually weren't correct
>     for a 100!
>     I bought  pair from Kent Lacy that were from the very low mileage
>     car that he had and they are quite different.  I understand that
>     the A B cases were actually correct for an MGA.
>     This is, I believe, what the original Lucas battery used in the
>     100 looked like.
>     M
>
>
>
>     ------------------------------------------------------------------------
>     *From:* Hank Leach <gradea1@charter.net>
>     *Sent:* Saturday, 14 November 2026 12:56:31
>     *To:* simon.lachlan@alexarevel.plus.com
>     <simon.lachlan@alexarevel.plus.com>
>     *Cc:* michael.salter@gmail.com <michael.salter@gmail.com>; Healey
>     team <healeys@autox.team.net>
>     *Subject:* RE: RE: [Healeys] The Story of Positive Earth (and
>     Electrics 101)
>     Simon-long story about batteries. The brief answer is they are
>     originally Lucas style (licensed) made by Antique Battery in
>     Pennsylvania. (now out of business) They were dry charged and
>     about $300 each. They lasted about 3 years and spit acid all over
>     my RE and axle as they gassed/vented. Finally, in desperation I
>     went to one universal 12V on the passenger (here RT side) which
>     fit the tray.
>     Since they were so accurate in looks, I could not bring myself to
>     throw them away so I took Michael Salter's advice and cut them
>     open, discarding the plates, and that is how they now are; cleaned
>     up but empty-0 volts. I had intended to try Michaels solution but
>     he did not have good results with the underpowered and dangerous
>     Lithium batteries, so I am still in search of a 12V. AGM
>     (Lead/acid-sealed) unit small enough to fit inside the case. (like
>     an ATV size) That would be a safer sealed battery. Not yet found
>     one with enough CCA.
>     In the meantime I am preparing the dummy side(LH) to be just a
>     connection to ground, so that looking into the compartment, all
>     looks sort of correct. There is a company on eBay, presently
>     making one look-a-like 17L but without Lucas logo as they could
>     not get Lucas to approve them-still costing $350 each and also dry
>     charged old style spitting acid type. These I don't want.
>     So as good as they look they are not currently functional in my
>     100. Sad story. Waiting for Michael to come up with a solution.
>     Hope he finds something and then they can be POSITIVE GROUND. Hank
>
>     --------------------
>
>     From: <simon.lachlan@alexarevel.plus.com>
>     To: <gradea1@charter.net>
>     Sent: November 14, 2026 at 1:27 AM PST
>     Subject: RE: [Healeys] The Story of Positive Earth (and Electrics 101)
>
>     Great pics. Batteries look new. For interestâ??s sake â?? I have a BT7
>     â?? are they repros or are they still available or did you rebuild
>     them with modern stuff inside?
>
>     They remind me somewhat of what our army called FFR Landrovers.
>     (Fitted For Radio). Long wheel base, there were 4 BIG 12v
>     batteries in the back. Hooked up in series and parallel so they
>     pushed out 24v. Used by signallers. I always thought the latter
>     were a necessary waste of space as they were always so intent on
>     signals that they never ran the engine in order to keep the
>     batteries charged. Those vehicles were a pig to start with a crank
>     handle.
>
>     Simon
>
>  

--------------Je0imF3Uiswqt1AGno0OISDm
Content-Transfer-Encoding: 8bit

<!DOCTYPE html>
<html>
  <head>
    <meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
  </head>
  <body>
    Nope.<br>
    <br>
    <div class="moz-cite-prefix">On 11/14/2026 11:18 PM,
      <a class="moz-txt-link-abbreviated" 
href="mailto:josef-eckert@t-online.de";>josef-eckert@t-online.de</a> wrote:<br>
    </div>
    <blockquote type="cite"
cite="mid:1794727138791.187398.de6010d65392748982ca71eb5333e6a3f1314fae@spica.telekom.de">
      <meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
      <title></title>
      <p><span
style="font-family: arial,helvetica,sans-serif; font-size: 10pt; color: 
#000000; text-decoration: none;">I
          think that´s far over the top what you do. Have you ever tried
          just one of the two batteries?</span></p>
      <p><span
style="font-family: arial,helvetica,sans-serif; font-size: 10pt; color: 
#000000; text-decoration: none;">I
          use just one Harley Davidson motorcycle 12Volt, 35 Ah, battery
          which is covered by the original battery body top, left and
          right side. Only front and rear of the battery are not
          covered, which can´t be seen. The second is just a dummi. That
          works fine for me and it always gets the engine cranked in
          full speed to start it.</span></p>
      <p> </p>
      <p><span
style="font-family: arial,helvetica,sans-serif; font-size: 10pt; color: 
#000000; text-decoration: none;">Josef
          Eckert</span></p>
      <p><span
style="font-family: arial,helvetica,sans-serif; font-size: 10pt; color: 
#000000; text-decoration: none;">Konigswinter.
          Germany</span></p>
      <p><span
style="font-family: arial,helvetica,sans-serif; font-size: 10pt; color: 
#000000; text-decoration: none;"> </span></p>
      <p> </p>
      <p> </p>
      <p> </p>
      <p>-----Original-Nachricht-----</p>
      <p>Betreff: Re: [Healeys] The Story of Positive Earth (and
        Electrics 101)</p>
      <p>Datum: 2026-11-15T04:24:13+0100</p>
      <p>Von: "Bob Spidell via Healeys" <a class="moz-txt-link-rfc2396E" 
href="mailto:healeys@autox.team.net";>&lt;healeys@autox.team.net&gt;</a></p>
      <p>An: <a class="moz-txt-link-rfc2396E" 
href="mailto:healeys@autox.team.net";>"healeys@autox.team.net"</a> <a 
class="moz-txt-link-rfc2396E" 
href="mailto:healeys@autox.team.net";>&lt;healeys@autox.team.net&gt;</a></p>
      <p> </p>
      <p> </p>
      <p> </p>
      <div
style="position: relative; color: #000000; font: 12px 
Arial,Helvetica,sans-serif;">I
        got fed up with the 17H 6Vs I'd used for years; they were hard
        to find, would barely crank my BN2's (170+psi on all 4) rebuilt
        starter and came close to contacting the lid. So, I threw in the
        towel on original. IIRC, these are over 450CCA so two in
        parallel give close to 900A, with 00 cables linking them in
        parallel. The starter sounds stronger than my BJ8's with a
        500CCA AGM.<br>
        <br>
        <a class="moz-txt-link-freetext"
          href="https://4xspower.com/collections/d-series-batteries";
          
moz-do-not-send="true">https://4xspower.com/collections/d-series-batteries</a> 
            (NFI). <br>
        <br>
        <br>
        If my (rudimentary) knowledge is correct, inductive loads like
        starters are almost dead shorts for a few milliseconds, until
        impedance builds as the motor starts to rotate (hence 450 amps).
        Besides the current draw, there will be a voltage drop, which
        reduces cranking power. I'd be interested in a voltage reading
        during cranking; old school load testers--the kind with carbon
        pile resistance--use the voltage drop to determine if a battery
        is good (and they usually test for 30 seconds or more). Of
        course, cold 20W/50 oil doesn't facilitate easy starting. <br>
        <br>
        One of my tractors--an early Ford--had a single 6V battery and
        pos. gnd. and starting it was a coin toss. It would only crank,
        very slowly, for about 20 seconds before giving up the ghost. I
        recently converted it to 12V neg. gnd. and it snaps to life on
        the first or second crank.<br>
        <br>
        Bob<br>
        <br>
        <br>
        <div class="moz-cite-prefix">On 11/14/2026 10:52 AM, Michael
          Salter wrote:</div>
        <blockquote
cite="mid:CAB3i7L+r2dJCo_OGLTKZ=xHCJa2XKRoM7cpS9SE23k0B8+tMpQ@mail.gmail.com">
          <div dir="auto">
            <div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">Interesting
                that you should bring this subject up Hank. I'm always
                on the lookout for a solution but, as yet not much has
                shown up.</div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">The
                primary issue is the "stalled" current draw of the M418
                starter motor of around 450 amps.</div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">I
                have found a 12 volt battery which will fit into the
                case which delivers 225 amps. </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">Tests
                on my BN1 with around 9.5: 1 compressions show that it
                can draw something like 280 amps on a cold day at first
                attempt with 20/50 oil. </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">Once
                it has cranked over a few times this drops to under 200
                amps. </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">My
                BN2 with its standard 7.5:1 compressions only draws
                around 130 amps from cold.</div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">I'm
                working with a battery company at present who have a
                "power sports" battery which would fit into the original
                case which delivers 225 CCA so it's likely that that
                battery would work with the BN2 but, because it is fuel
                injected I'm still trying to figure out if that battery
                has sufficient reserve capacity to provide the 8 amps
                the EFI system requires for sufficient time at idle. </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">BTW,
                not wanting to burst your bubble but I'm fairly sure now
                that the 17L cases suppied by Antique Battery actually
                weren't correct for a 100! </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">I
                bought  pair from Kent Lacy that were from the very low
                mileage car that he had and they are quite different.  I
                understand that the A B cases were actually correct for
                an MGA.</div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">This
                is, I believe, what the original Lucas battery used in
                the 100 looked like.</div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;"> </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">M</div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;"><br>
                <br>
                <br>
              </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt;">
                <div
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt;"> </div>
              </div>
              <div dir="auto"
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;">
                <div
style="font-family: 
Aptos,Aptos_MSFontService,-apple-system,Roboto,Arial,Helvetica,sans-serif; 
font-size: 12pt; color: #212121;"> </div>
              </div>
              <hr style="display: inline-block; width: 98%;">
              <div dir="ltr"><span
style="font-size: 11pt; color: #000000; font-family: Calibri, 
sans-serif;"><strong>From:</strong>
                  Hank Leach &lt;<a class="moz-txt-link-freetext"
                    href="mailto:gradea1@charter.net"; rel="noreferrer"
                    moz-do-not-send="true">gradea1@charter.net</a>&gt;<br>
                  <strong>Sent:</strong> Saturday, 14 November 2026
                  12:56:31<br>
                  <strong>To:</strong> <a class="moz-txt-link-freetext"
                    href="mailto:simon.lachlan@alexarevel.plus.com";
                    rel="noreferrer" 
moz-do-not-send="true">simon.lachlan@alexarevel.plus.com</a>
                  &lt;<a class="moz-txt-link-freetext"
                    href="mailto:simon.lachlan@alexarevel.plus.com";
                    rel="noreferrer" 
moz-do-not-send="true">simon.lachlan@alexarevel.plus.com</a>&gt;<br>
                  <strong>Cc:</strong> <a class="moz-txt-link-freetext"
                    href="mailto:michael.salter@gmail.com";
                    rel="noreferrer" 
moz-do-not-send="true">michael.salter@gmail.com</a>
                  &lt;<a class="moz-txt-link-freetext"
                    href="mailto:michael.salter@gmail.com";
                    rel="noreferrer" 
moz-do-not-send="true">michael.salter@gmail.com</a>&gt;;
                  Healey team &lt;<a class="moz-txt-link-freetext"
                    href="mailto:healeys@autox.team.net";
                    rel="noreferrer" 
moz-do-not-send="true">healeys@autox.team.net</a>&gt;<br>
                  <strong>Subject:</strong> RE: RE: [Healeys] The Story
                  of Positive Earth (and Electrics 101)</span>
                <div> </div>
              </div>
              <div>
                <div>Simon-long story about batteries. The brief answer
                  is they are originally Lucas style (licensed) made by
                  Antique Battery in Pennsylvania. (now out of business)
                  They were dry charged and about $300 each. They lasted
                  about 3 years and spit acid all over my RE and axle as
                  they gassed/vented. Finally, in desperation I went to
                  one universal 12V on the passenger (here RT side)
                  which fit the tray.</div>
                <div> </div>
                <div>Since they were so accurate in looks, I could not
                  bring myself to throw them away so I took Michael
                  Salter's advice and cut them open, discarding the
                  plates, and that is how they now are; cleaned up but
                  empty-0 volts. I had intended to try Michaels solution
                  but he did not have good results with the underpowered
                  and dangerous Lithium batteries, so I am still in
                  search of a 12V. AGM (Lead/acid-sealed) unit small
                  enough to fit inside the case. (like an ATV size) That
                  would be a safer sealed battery. Not yet found one
                  with enough CCA.</div>
                <div> </div>
                <div>In the meantime I am preparing the dummy side(LH)
                  to be just a connection to ground, so that looking
                  into the compartment, all looks sort of correct. There
                  is a company on eBay, presently making one look-a-like
                  17L but without Lucas logo as they could not get Lucas
                  to approve them-still costing $350 each and also dry
                  charged old style spitting acid type. These I don't
                  want.</div>
                <div> </div>
                <div>So as good as they look they are not currently
                  functional in my 100. Sad story. Waiting for Michael
                  to come up with a solution. Hope he finds something
                  and then they can be POSITIVE GROUND. Hank</div>
                <div><br>
                  -------------------- <br>
                  <br>
                  From: &lt;<a class="moz-txt-link-freetext"
                    href="mailto:simon.lachlan@alexarevel.plus.com";
                    rel="noreferrer" 
moz-do-not-send="true">simon.lachlan@alexarevel.plus.com</a>&gt;
                  <br>
                  To: &lt;<a class="moz-txt-link-freetext"
                    href="mailto:gradea1@charter.net"; rel="noreferrer"
                    moz-do-not-send="true">gradea1@charter.net</a>&gt; <br>
                  Sent: November 14, 2026 at 1:27 AM PST <br>
                  Subject: RE: [Healeys] The Story of Positive Earth
                  (and Electrics 101)</div>
                <div>
                  <p>Great pics. Batteries look new. For interestâ??s sake
                    â?? I have a BT7 â?? are they repros or are they still
                    available or did you rebuild them with modern stuff
                    inside?</p>
                  <p>They remind me somewhat of what our army called FFR
                    Landrovers. (Fitted For Radio). Long wheel base,
                    there were 4 BIG 12v batteries in the back. Hooked
                    up in series and parallel so they pushed out 24v.
                    Used by signallers. I always thought the latter were
                    a necessary waste of space as they were always so
                    intent on signals that they never ran the engine in
                    order to keep the batteries charged. Those vehicles
                    were a pig to start with a crank handle.</p>
                  <p>Simon</p>
                  <p> </p>
                </div>
              </div>
            </div>
          </div>
        </blockquote>
      </div>
      <p> </p>
      
    </blockquote>
    <br>
  </body>
</html>

--------------Je0imF3Uiswqt1AGno0OISDm--

--===============5189488682828184288==
Content-Transfer-Encoding: 7bit
Content-Disposition: inline

_______________________________________________

Archive: http://www.team.net/pipermail/healeys 
http://autox.team.net/archive/healeys

Healeys@autox.team.net
http://autox.team.net/mailman/listinfo/healeys



--===============5189488682828184288==--

<Prev in Thread] Current Thread [Next in Thread>